Toshiba RAS-B10N3KV2-E Service Manual Download Page 87

Page: 87 / 105

–

No.

Horizontal louver

Procedures

1) Remove shaft of the horizontal

louver from the back body.
(First remove the left shaft, and
then remove other shafts while
sliding the horizontal louver
leftward.)

Evaporator
(Heat exchanger)

1) Follow to the procedure in the item

2) Remove the pipe holder from the rear side of the main unit.

3) Remove two fixing screws at the left side of the end plate of the heat exchanger.

Remarks

4) Remove one fixing screw on the

heat exchage fixing holder to separate the
heat exchage from the back body.

5) Remove right side of the end plate from

two fixing rib while sliding slightly the
heat exchanger rightward.

2 screws

Heat exchanger fixing
holder

Screw

Rib on the right side of the end plate

Part name

FILE NO. SVM-12050

Summary of Contents for RAS-B10N3KV2-E










































































































Search results

Summary of Contents for RAS-B10N3KV2-E

Reviews:

Related manuals for RAS-B10N3KV2-E

Brands by name

Popular brands

Toshiba RAS-B10N3KV2-E, Service Manual

Search results

Summary of Contents for RAS-B10N3KV2-E

Reviews:

Related manuals for RAS-B10N3KV2-E

Brands by name

Popular brands