background image

– 13 –

Selection of pipe size

No.

Title

Use part

Selection of pipe size

Remarks

(1)

Outdoor unit 

connecting pipe

Outdoor unit

Outdoor unit 

connection piping 

kit

(2)

Between Outdoor 

unit connection 

piping 
*6

Outdoor unit 

connection piping 

kit

Outdoor unit 

connection piping 

kit

(3)

Main piping

Outdoor unit 

connection piping 

kit of header unit

First branching 

section

Pipe size differs based 

on the total capacity 

codes of all outdoor 

units (See Table 2.)

(4)

Branching pipe
*1, *2, *6

Branching section

Branching section

Branching section

Flow Selector unit

Flow Selector unit

Branching section

Pipe size differs based 

on the total capacity 

code value of indoor 

units at the 

downstream side. 

(See Table 1 and 2.)

(5)

Indoor unit 

connecting pipe

Flow Selector unit

Indoor unit

Model

Balance pipe 

side

Suction gas 

side

Discharge 

gas side

Liquid side

MAP080

Ø9.5

Ø22.2

Ø19.1

Ø12.7

MAP100

Ø9.5

Ø22.2

Ø19.1

Ø12.7

MAP120

Ø9.5

Ø28.6

Ø19.1

Ø12.7

MAP140

Ø9.5

Ø28.6

Ø22.2

Ø15.9

Total capacity codes of outdoor units at 

the downstream side

Suction 

gas side

Discharge 

gas side

Liquid 

side

Equivalent to 

capacity

Equivalent to HP

45.0 to below 61.5

16 to below 22

Ø28.6

Ø22.2

Ø15.9

 61.5 to below 73.0

22 to below 26

Ø34.9

Ø28.6

Ø19.1

 73.0 or more

26 or more

Ø34.9

Ø28.6

Ø19.1

Total capacity codes of all 

outdoor units

Suction 

gas 

side

Discharge 

gas side

Liquid 

side

Equivalent to 

capacity

Equivalent to 

HP

 22.4 to below 33.5

8 to below 12

Ø22.2

Ø19.1

Ø12.7

 33.5 to below 38.4

12 to below 14

Ø28.6

Ø19.1

Ø12.7

 38.4 to below 45.0

14 to below 16

Ø28.6

Ø22.2

Ø15.9

 45.0 to below 61.5

16 to below 22

Ø28.6

Ø22.2

Ø19.1

 61.5 to below 73.0

22 to below 26

Ø34.9

Ø28.6

Ø19.1

 73.0 to below 101.0

26 to below 36

Ø34.9

Ø28.6

Ø22.2

101.0 or more

36 or more

Ø41.3

Ø34.9

Ø22.2

Total capacity codes of indoor 

units at the downstream side

Suction 

gas 

side

Discharge 

gas side

Liquid 

side

Equivalent to 

capacity

Equivalent to 

HP

Below 18

Below 6.4

Ø15.9

Ø12.7

Ø9.5

18 to below 34

6.4 to below 12.2

Ø22.2

Ø19.1

Ø12.7

34 to below 45.5

12.2 to below 16.2 Ø28.6

Ø22.2

Ø15.9

45.5 to below 56.5 16.2 to below 20.2 Ø28.6

Ø22.2

Ø19.1

56.5 to below 70.5 20.2 to below 25.5 Ø34.9

Ø28.6

Ø19.1

70.5 to below 98.5 25.2 to below 35.2 Ø34.9

Ø28.6

Ø22.2

98.5 or more

35.2 ore more

Ø41.3

Ø34.9

Ø22.2

Capacity rank

Equivalent to HP

Gas side

Liquid side

007 to 012

0.8 to 1.25

Ø9.5

Ø6.4

015 to 018

1.7 to 2.0

Ø12.7

Ø6.4

024 to 056

2.5 to 6.0

Ø15.9

Ø9.5

072 to 096

8.0 to 10.0

Ø22.2

Ø12.7

*1: Use the same size as the main pipe if it is larger than the main pipe.
*2: Use a suction gas pipe and a liquid pipe for the two pipes branching downstream from the flow selector unit and the dedicated cooling circuit.
*3: Select the branch pipe of the first branch according to the outdoor capacity code.
*4: Select according to the outdoor unit capacity code if the total of the indoor capacity codes exceeds the outdoor unit capacity code.
*5: It is possible to select up to a maximum capacity code total AP056 (6 hp) for the first circuit after the header branch.

When using a branch header for the first branch with an outdoor unit capacity code of 33.5 (12 hp equivalent) or more and 73.0 (26 hp 

equivalent) or less, use RBM-HY2043FE (4 branches) and RBM-HY-2083FE (8 branches) regardless of the total value of the capacity 

codes of the downstream indoor units. And, a branch header cannot be used as the first branch if the performance rank is over 73.0 (26 hp 

equivalent). 

*6: The downstream starting point is the main pipe.
*7: Only group operation with one remote controller (or two remote controllers) is possible if one flow selector unit is connected to multiple 

indoor units.

(6)

Indoor unit 

connecting pipe

Terminal 

branching section

Indoor unit

(7)

Y-shaped 

branching joint
*3, *4

Branching section

(8)

Branching header
*3, *4, *5

Branching section

(9)

Outdoor unit 

connection piping 

kit
*6

Branching section

(10)

Flow Selector unit
*7

No.

Title

Use part

Selection of pipe size

Remarks

Capacity rank Equivalent to 

HP

Length of piping

Gas side

Liquid 

side

007 to 012

0.8 to 1.25

15 m or less real length

Ø9.5

Ø6.4

Exceeds 15 m real length

Ø12.7

Ø9.5

015 to 018

1.7 to 2.0

15 m or less real length

Ø12.7

Ø6.4

Exceeds 15 m real length

Ø15.9

Ø9.5

024 to 056

2.5 to 6.0

-

Ø15.9

Ø9.5

072 to 096

8.0 to 10.0

-

Ø22.2

Ø12.7

Total capacity code of indoor units

Model name

Equivalent to capacity Equivalent to HP

For 3 piping

For 2 piping

Below 18.0

Below 6.4

RBM-BY55FE

RBM-BY55E

18.0 to below 40.0

6.4 to below 14.2

RBM-BY105FE

RBM-BY105E

40.0 to below 70.5

14.2 to below 25.2

RBM-BY205FE

RBM-BY205E

70.5 or more

25.2 or more

RBM-BY305FE

RBM-BY305E

Total capacity code of indoor units

Model name

Equivalent to 

capacity

Equivalent to 

HP

For 3 piping

For 2 piping

For 4 

branches

Below 40.0

Below 14.2

RBM-HY1043FE

RBM-HY1043E

40.0 to below 70.5 14.2 to below 25.2 RBM-HY2043FE

RBM-HY2043E

For 8 

branches

Below 40.0

Below 14.2

RBM-HY1083FE

RBM-HY1083E

40.0 to below 70.5 14.2 to below 25.2 RBM-HY2083FE

RBM-HY2083E

Total capacity codes of outdoor units at the 

downstream side

Model name

Equivalent to capacity

Equivalent to HP

Below 73.0

Below 26.0

RBM-BT14FE

73.0 or more

26.0 or more

RBM-BT24FE

Total capacity codes of connected indoor units

Model name

Equivalent to 

capacity

Equivalent to HP

Max. No. of 

connected indoor 

unit

Below 11.2

Below 4.0

Below 5

RBM-Y1123FE

11.2 to below 18.0

4.0 to below 6.4

Below 8

RBM-Y1803FE

18.0 to 28.0 or less

6.4 to below 10.0

Below 8

RBM-Y2803FE

25-EN

26-EN

Summary of Contents for MMY-MAP0804FT8-E






































Reviews: