manualshive.com logo in svg

Toshiba MMC-AP0151H, Service Manual

The Toshiba MMC-AP0151H Installation Manual is a comprehensive guide that provides step-by-step instructions for setting up and utilizing this product to its full potential. This manual can be easily accessed and downloaded for free from manualshive.com, ensuring a hassle-free user experience without any additional costs.

Share
Download
background image

147

Error detected by TCC-LINK central control device

Check code

Display on

central control

device

C05

C06

C12

P30

Outdoor 7-segment display

Sub-code

—

—

—

(L20 is displayed.)

AI-NET

central control

remote controller

—

—

—

Detected

position

TCC-LINK

General-

purpose device

I/F

TCC-LINK

Check code name

TCC-LINK central control
device transmission error

TCC-LINK central control
device receiving error

Interface batch alarm of
general-purpose control
devices

Follower unit error of
group control

Duplicated central
control address

Status

Operation

continued.

Operation

continued.

Operation

continued.

Operation

continued.

Operation

continued.

Error detection condition

Signal is not transmit from
central control device.

Signal is not received from
central control device.

Error was input in general-
purpose control device
control interface.

An error occurred in follower
unit of the group control.
([P30] is displayed only on
the central control remote
controller.)

Central control addresses
were duplicated.

Check item (position)

• Check central control device error.
• Check communication line error of central control device.
• Check setup of end terminal resistance.

• Check central control device error.
• Check communication line error of central control device.
• Check setup of end terminal resistance.
• Check the power of connecting destination connected device.
• Check P.C. board error of the connected device.

• Check error input.

• Check the check code of the unit with alarm.

• Check the address setup.

Differs according to error contents of the with
alarm

Error detected by AI-NET central control device

Check code

Main

remote

controller

—

—

—

Outdoor 7-segment display

Check code

Sub-code

—

—

—

—

—

—

AI-NET

central control

remote controller

97

99

b7

Detected

position

AI-NET

AI-NET

AI-NET

Check code name

AI-NET communication
system error

Duplicated network
adaptors

Error in indoor group

Status

Operation

continued.

Operation

continued.

Operation

continued.

Error detection condition

E07/L07/L03/L08 was
detected when other indoor
unit in the group was
defective.

Multiple network adaptors
were connected to
communication line of
remote controller.
(Detected at central
controller side)

Error of follower unit in the
group

Check item (position)

• Check multiple network adaptors.
• Check wire and miscabling of remote controller: Only one network

adaptor can be connected to communication line of remote
controller.

• Check communication line, miscabling, and power of indoor unit.
• Check communication. (X, Y terminals)
• Check network adaptor P.C. board.
• Check the central controller (Central control remote controller, etc.)

• Check follower unit in the group.

∗

These errors are concerned to communication of remote controllers (A, B) and central system [AI-NET X, Y], and the main remote controller displays [E01], [E02], [E03], [E09], or
[E18] in some cases and displays none in other cases according to the contents.

Summary of Contents for MMC-AP0151H















































































































































































































































































Reviews:

No comments

Related manuals for MMC-AP0151H

acerpure pro Series User Manual preview
pro Series
Brand: acerpure Pages: 48
BAC S1500E Rigging And Installation Instructions preview
S1500E
Brand: BAC Pages: 28
Jafanda JF100 User Manual preview
JF100
Brand: Jafanda Pages: 6
Kahn ATOM User Handbook Manual preview
ATOM
Brand: Kahn Pages: 8
AAF HCFA 2424 Installation, Operation And Maintenance Manual preview
HCFA 2424
Brand: AAF Pages: 12
TATA Motors TSR Series Installation, Use And Manteinance Manual preview
TSR Series
Brand: TATA Motors Pages: 32
Dimplex DCEVP6WT Instruction Manual preview
DCEVP6WT
Brand: Dimplex Pages: 16
Prinetti IA5036 Instruction Manual preview
IA5036
Brand: Prinetti Pages: 32
Zephir ZPA90 Manual preview
ZPA90
Brand: Zephir Pages: 19
Omega Altise OAPC41W Operation, Maintenance And Safety Instructions preview
OAPC41W
Brand: Omega Altise Pages: 24
Mars B-DVH09SF-0 User Manual preview
B-DVH09SF-0
Brand: Mars Pages: 20
Pinguino PAC T110P Instructions For Use Manual preview
PAC T110P
Brand: Pinguino Pages: 36
AireSpa ASWRB100 Use & Care Manual preview
ASWRB100
Brand: AireSpa Pages: 20
Panasonic CS/CU-HU12ZKY Series Operating & Installation Instructions Manual preview
CS/CU-HU12ZKY Series
Brand: Panasonic Pages: 32
Samsung APC503QG User Manual preview
APC503QG
Brand: Samsung Pages: 24
Samsung AMxxxNN1PEH Series User Manual preview
AMxxxNN1PEH Series
Brand: Samsung Pages: 24
Samsung APC2480B Owner'S Instructions Manual preview
APC2480B
Brand: Samsung Pages: 28
Samsung AP30N0A User Manual preview
AP30N0A
Brand: Samsung Pages: 32

Brands by name

Popular brands

Load more brands