Toshiba MMC-AP0151H Service Manual Download Page 136

Page: 136 / 270

136

9-4. Check Code and Check Position Displayed on the Remote Controller and Outdoor Unit

(7-Segment Display of Interface)

Check code

Main

remote

controller

E01

E02

E03

E04

E06

—

E08

E09

E10

Outdoor 7-segment display

Check code

Sub-code

—

E06

No. of indoor units which
received signal normally

E07

—

E08

Duplicated indoor
addresses

—

AI-NET

central control

remote controller

—

Detected
position

Remote

controller

Remote

controller

Indoor

unit

Indoor

unit

I/F

Indoor

I/F

Remote

controller

Indoor

unit

Check code name

Communication error between
indoor and remote controller
(Detected at remote controller side)

Remote controller sending error

Communication error between
indoor and remote controller
(Detected at indoor side)

Indoor/outdoor communication
circuit error
(Detected at indoor side)

Decreased number of indoor units

Indoor/outdoor communication
circuit error
(Detected at outdoor side)

Duplicated indoor addresses

Duplicated master remote
controllers

Communication error between
indoor P.C. board assembly

Status

Corresponding

unit only stops.

Corresponding

unit only stops.

Corresponding

unit only stops.

Corresponding

unit only stops.

All stop

Corresponding

unit only stops.

Corresponding

unit only stops.

Error detection condition

Communication interrupted
between indoor P.C. board and
remote controller.

Signal could not be sent from
remote controller to indoor unit.

No communication from remote
controller (including wireless) and
communication adaptor.

Indoor unit does not receive
communication from outdoor unit.

When signal is not sent for a
certain period from the indoor
unit which has been used to
send signals, [E06] is normally
displayed.

Transmission from outdoor to
indoor cannot continue for 30
seconds.

Multiple indoor unit address
setup are duplicated.

In 2-remote controller control
(including wireless), both are
setup as master
(Header indoor unit stops and
other indoor unit is operating.)

There is any trouble in power
line.

Check item (position)

• Check remote controller inter-unit cable (A/B).
• Check disconnection, connector contact error.
• Check indoor power supply.
• Check indoor P.C. board error.
• Check remote controller address setup.

(When two remote controllers operate)

• Check remote controller P.C. board.

• Check the communication wire of remote

controller: Exchange remote controller.

• Check remote controller and communication

adaptor wiring.

• Check power-ON order of indoor/outdoor.
• Check indoor address setup.
• Check inter-unit cabling between indoor and

outdoor.

• Check outdoor end terminal resistance setup

(SW30-2).

• Check the power supply of indoor unit.

(Power-ON)

• Check connection of communication line

between indoor and outdoor.

• Check connector connection for communication

in indoor P.C. board.

• Check connector connection for communication

in outdoor P.C. board.

• Check indoor P.C. board failure.
• Check outdoor P.C. board (I/F) failure.

• Check outdoor end terminal resistance setup

(SW30-2).

• Check the communication connection between

indoor and outdoor.

• Check indoor address.
• Check the change of remote controller

connection (Group / individual) after setup of
indoor address.

• Check remote controller setup.
• Check remote controller P.C. board.

• Indoor P.C. board failure

Summary of Contents for MMC-AP0151H















































































































































































































































































Search results

Summary of Contents for MMC-AP0151H

Reviews:

Related manuals for MMC-AP0151H

Brands by name

Popular brands

Toshiba MMC-AP0151H, Service Manual

Search results

Summary of Contents for MMC-AP0151H

Reviews:

Related manuals for MMC-AP0151H

Brands by name

Popular brands