Toshiba G8000MM Series Installation And Operation Manual Download

Page: 100 / 104

G8000MM

Installation and Operation Manual

Installation Planning Guide for G8000MM 750kVA UPS

Standard System: 480V Input, 480Y/277V Output

General Mechanical Information

Dimensions

(W x D x H*)

Weight

Floor

Approximate Full-Load
Heat Rejection

Mechanical Clearance (Inches)from UPS
for Ventilation and Maintenance Access

Inches

Lbs.

Lbs./ft.

Btu/Hr

Top

Front

Bottom Sides**

Back

129.9” x 49.5” x 79.7” 9,193

207

144,407

24”

43”

0”

1”

0”

* Height includes removable fan housing – Frame height is 78.7.”
** 0” clearance for peripheral equipment, 1” clearance for walls.

Primary AC Input (480V 3-Phase / 3-Wire)

Maximum Input Power Demand
Normal Mode (Recharge Mode)

Suggested External

Overcurrent Protection

External Feeder Wire Size: Min. – Max. Per Phase

kVA

Amps

AWG or kcmil at 75º C Temp. Rating

732 (776)

>0.98

880 (934)

1200 AT

(3) x 600 kcmil – (4) x 400 kcmil

Alternate (Bypass) AC Input (480V 3-Phase / 4-Wire)

Maximum Input Power

Demand

Suggested External

Overcurrent Protection

External Feeder Wire Size:

Min. – Max. Per Phase // Min. – Max. for Neutral

kVA

Amps

AWG or kcmil at 75º C Temp. Rating

750

0.9

902

1200 AT

(3) x 600 kcmil – (4) x 400 kcmil //

(5) x 500 kcmil – (5) x 600 kcmil

Battery Input (480VDC Nominal)

Battery Capacity Required

for Full Load Output

Maximum Discharge

at Full Load Output

Suggested External

Overcurrent Protection

External Feeder Wire Size: Min. – Max.

kWB

Amps DC

Amps

AWG or kcmil at 75º C Temp. Rating

718

1792

2000 AT

(6) x 400 kcmil – (6) x 500 kcmil

AC Output (480/277V 3-Phase / 4-Wire)

Rated Output Power

Suggested External

Overcurrent Protection

External Feeder Wire Size:

Min. – Max. Per Phase // Min. – Max. for Neutral

kVA

Amps

AWG or kcmil at 75º C Temp. Rating

750

0.9

902

1200 AT

(3) x 600 kcmil – (4) x 400 kcmil //

(5) x 500 kcmil – (5) x 600 kcmil

Important Notes:

Maximum Current required at Primary AC Input based on
full load output and maximum battery charging current.

Output load conductors are to be installed in separate

conduit from input conductors.

Control wires and power wires are to be installed in

separate conduits.

Recommended AC input and output overcurrent protection

based on continuous full load current per NEC.

Wiring shall comply with all applicable national and local

electrical codes.

Grounding conductors to be sized per NEC Article

250-122. Neutral conductors to be sized per NEC Article
310.15.

Primary AC Input: 3 , 3-wire + ground.

Alternate AC Input: 3 , 4-wire + ground.

AC Output: 3 , 4-wire + ground.

DC Input: 2-wire (Positive/Negative) + ground.

Nominal battery voltage based on the use of VRLA type

batteries (2.0 volts/cell nominal).

Maximum battery discharge current based on lowest

permissible discharge voltage of 1.67 VPC.

DC wires should be sized to allow not more than a 2-volt

drop at maximum discharge current.

10. Weights do not include batteries or other auxiliary equipment

external to the UPS.

11. Cable sizing calculations based on the following assumptions:

Minimum size is smallest size based on ampacity at 30 C.

No more than three current carrying conductors per conduit.

Neutral sized for 2 X phase current.

Temperature rating of copper conductors/terminals: 75 C.

Reference: 2005 NEC Handbook, Table 310.16.

NOTE: Consult latest edition of applicable
national and local codes for possible
variations.

12. Ratings of wires and overcurrent devices are suggested

minimums. Consult with a registered Professional Engineer
within your local area for proper size selections.

TOSHIBA

INTERNATIONAL CORPORATION

13131 West Little York Road
Houston, TX 77041
Telephone: (800) 231-1412
Fax: (713) 896-5212
Web Site:

www.toshiba.com/ind

1/3

Summary of Contents for G8000MM Series









































































































Search results

Summary of Contents for G8000MM Series

Reviews:

Related manuals for G8000MM Series

Brands by name

Popular brands

Toshiba G8000MM Series, Installation And Operation Manual

Search results

Summary of Contents for G8000MM Series

Reviews:

Related manuals for G8000MM Series

Brands by name

Popular brands