background image

 

G8000MM Installation and Operation Manual 

 

iii 

 

List of Figures 

 

Figure 1.1 

Single Line Diagram – Normal Operation ...........................................................    8 

Figure 1.2 

Single Line Diagram – Bypass Operation ...........................................................    9 

Figure 1.3 

Single Line Diagram – Battery Operation ...........................................................  10 

Figure 1.4.a 

UPS Parts Location (100, 150, 225 kVA) ............................................................  11 

Figure 1.4.b 

UPS Parts Location (300, 375 kVA) ....................................................................  11 

Figure 1.4.c 

UPS Parts Location (500 kVA) ............................................................................  12 

Figure 1.4.d 

UPS Parts Location (625, 750 kVA) ....................................................................  13 

Figure 1.5 

UPS Parts Location .............................................................................................  14 

Figure 1.6 

External I/F PCB IOAU-04   .................................................................................  14 

Figure 2.1 

Operation/Display Panel ......................................................................................  21 

Figure 2.2 

Main Screen ........................................................................................................  23 

Figure 2.3 

Start/Stop Screen ................................................................................................  23 

Figure 2.4 

PIN Protection Screen .........................................................................................  23 

Figure 2.5 

Bypass Voltage Abnormal Message    Screen ....................................................  23 

Figure 2.6 

Measurement Screen ..........................................................................................  23 

Figure 2-7 

Setup Screen .......................................................................................................  24 

Figure 2-8 

Log select Screen ................................................................................................  24 

Figure 2-9 

Event Log Screen ................................................................................................  24 

Table 2-10 

Battery Log Screen ..............................................................................................  25 

Figure 2.11 

Main Screen (Battery Operation) ........................................................................  25 

Figure 2.12 

Measurement Screen (Battery Operation) ..........................................................  25 

Figure 2.13 

Main Screen (Fault Indication) ............................................................................  26 

Figure 2.14 

Message Screen..................................................................................................  26 

Figure 2.15.a  External Signal Terminal Block (NEC Class 2) TN1 ...........................................  28 
Figure 2.15.b  External Signal Terminal Block (NEC Class 2) TN2   .........................................  29 
Figure 2.16 

Control Wiring for External Contacts ...................................................................  30 

Figure 2.17 

Remote "Start" Contact Connections ..................................................................  31 

Figure 2.18 

External Communication Connector (NEC Class 2) ...........................................  32 

Figure 3.1 

UPS Terminal Designation   ................................................................................  38 

Figure 3.2.a.1  Diag. of Input/Output Bus Bars & Terminal Blocks (100/150/225 kVA, 480V)   .  39 
Figure 3.2.a.2  Diag. of Power Wire & Control Wire Inter-Connect (100/150/225 kVA, 480V) ...  40 
Figure 3.2.b.1  Diag. of Input/Output Bus Bars & Terminal Blocks (100/150/225 kVA, 600V)   .  41 
Figure 3.2.b.2  Diag. of Power Wire & Control Wire Inter-Connect (100/150/225 kVA, 600V) ...  42 
Figure 3.2.c.1  Diag. of Input/Output Bus Bars & Terminal Blocks (300/375 kVA, 480V)   ........  43 
Figure 3.2.c.2  Diag. of Power Wire & Control Wire Inter-Connect (300/375 kVA, 480V) ..........  44 
Figure 3.2.d.1  Diag. of Input/Output Bus Bars & Terminal Blocks (300/375 kVA, 600V)   ........  45 
Figure 3.2.d.2  Diag. of Power Wire & Control Wire Inter-Connect (300/375 kVA, 600V) ..........  46 
Figure 3.2.e.1  Diag. of Input/Output Bus Bars & Terminal Blocks (500/625/750 kVA, 480V)   .  47 
Figure 3.2.e.2  Diag. of Power Wire & Control Wire Inter-Connect (500/625/750    kVA, 480V)   48 

Summary of Contents for G8000MM Series









































































































Reviews: