Toshiba e-STUDIO557 Copying Manual Download Page 41

Page: 41 / 180

2.HOW TO MAKE COPIES

Bypass Copying 39

2 HOW TO MAKE COPIES

Bypass copying on standard size paper

Copying on A3, A4, B4 and B5 size paper (in equipment other than for North
America) / LD, LT, LG and ST-R size paper (in equipment for North America)

Place the original(s).

The height of the paper must not exceed the indicator on the side guides.

When you use more than one sheet of paper, fan the sheets well before placing them on the
bypass tray. Be careful not to cut your fingers when fanning.

Do not push paper into the entrance of the bypass feeder. This could cause a paper misfeed.

Select the same size button under “COPY” as that of the paper you placed on the
bypass tray.

The paper size is now set.

If the paper size is not selected in this step, copying may be slowed down.

Place paper with its copy side up on the bypass tray.
Then align the side guides to the paper length while
holding the tab.

When paper is placed, the menu for bypass copying appears.

Summary of Contents for e-STUDIO557




















































































































































































Search results

Summary of Contents for e-STUDIO557

Reviews:

Related manuals for e-STUDIO557

Brands by name

Popular brands

Toshiba e-STUDIO557, Copying Manual

Search results

Summary of Contents for e-STUDIO557

Reviews:

Related manuals for e-STUDIO557

Brands by name

Popular brands