Toshiba e-STUDIO203S, Service Manual

Page: 83 / 168

e-STUDIO203S/203SD TEST COMMAND, TROUBLE CODES 10 - 2
26 02 (R)ADF setting (ADF/RADF)
03 Second cassette setting (2ND TRAY)
04 Main unit duplex setting (DPLX)
06 Destination setting (DESTINATION)
07 Machine conditions check (CPM)
20 Rear edge void setting (END EDGE)
30 CE mark support control ON/OFF (CE MARK)
37 Cancel of stop at developer life over
(DVLP LIFE END)
39 Memory capacity check (MEM.CHK)
40 Polygon motor OFF time setting (Time required from
completion of printing to turning OFF the motor)
(LSU MOTOR OFF)
42 Transfer ON timing control setting (TC ON TIMING)
43 Side void amount setting (SIDE VOID)
54
γ
life correction setting (GAMMA CTRL)
62 Energy-save mode copy lamp setting (C-LAMP E-S)
30 01 Paper sensor status display (P-SENSOR)
41 06 OC cover float detection level adjustment
(OC FLOAT LEVEL)
07 OC cover float detection margin setting
(OC FLOAT MGN)
43 01 Fusing temperature setting (Normal copy) (FU TEMP)
04 Fusing temperature setting in multi copy
(FU TEMP MULTI)
05 Fusing temperature setting in duplex copy
(FU TEMP DPLX) (e-STUDIO203SD only)
14 Fusing start temperature setting (FU TEMP START)
46 01 Copy density adjustment (300dpi) (EXP.LEVEL 300)
02 Copy density adjustment (600dpi) (EXP.LEVEL 600)
12 Density adjustment in the FAX mode
(Collective adjustment)
(Executable only when the FAX is installed.)
13 FAX mode density adjustment (normal text)
(Executable only when the FAX is installed.)
14 FAX mode density adjustment (Fine text)
(Executable only when the FAX is installed.)
15 FAX mode density adjustment (Super fine)
(Executable only when the FAX is installed.)
18 Image contrast adjustment (300dpi) (GAMMA 300)
19 Exposure mode setting (AE MODE)
20 RADF exposure correction (EXP.LEVEL ADF)
29 Image contrast adjustment (600dpi) (GAMMA 600)
30 AE limit adjustment (AE LIMIT)
31 Image sharpness adjustment (SHARPNESS)
32 Copier color reproduction setting
(COLOR REAPPEAR)
39 FAX mode sharpness adjustment
(Executable only when the FAX is installed.)
48 01 Mains can/sub scan direction magnification ratio
(COPY MAG.)
05 RADF mode sub scan direction magnification ratio in
copying (RADF MAG.)
49 01 Download mode (DOWNLOAD MODE)
Main
code Sub
code
Contents
50 01 Lead edge image position (LEAD EDGE)
06 Copy lead edge position adjustment (RADF)
(RADF EDGE)
10 Print center offset adjustment (PRT.OFF-CENTER)
12 Document feed off-center adjustment
(ORG.OFF-CENTER)
18 Memory reverse position adjustment in duplex copy
(DPLX REVERSE)
19 Duplex copy rear edge void adjustment
(DPLX END EDGE) (e-STUDIO203SD only)
51 02 Resist amount adjustment (RESIST ADJ.)
53 08 RADF scan position automatic adjustment
(ADF AUTO)
61 03 HSYNC output check (LSU CHK)
63 01 Shading check (SHADING CHK)
02 Black level automatic correction (BLACK LEVEL)
12 Light quantity stable wait time setting
(LT.STABLE TIME)
13 Light quantity stable width setting (LT.STABLE RNG.)
64 01 Self print (1by2 mode) (SELF PRT.)
66 01 FAX soft SW setting
(Executable only when the FAX is installed.)
02 FAX soft SW initializing (excluding the adjustment
values) (Executable only when the FAX is installed.)
03 FAX PWB memory check
(Executable only when the FAX is installed.)
04 Signal send mode (Max. value)
(Executable only when the FAX is installed.)
05 Signal send mode (Soft SW set value)
(Executable only when the FAX is installed.)
07 Image memory content print
(Executable only when the FAX is installed.)
10 Image memory content clear
(Executable only when the FAX is installed.)
11 300bps signal send (Max. value)
(Executable only when the FAX is installed.)
12 300bps signal send (Soft SW set value)
(Executable only when the FAX is installed.)
13 Dial test (Executable only when the FAX is installed.)
17 DTMF signal send (Max. value)
(Executable only when the FAX is installed.)
18 DTMF signal send (Soft SW set value)
(Executable only when the FAX is installed.)
21 FAX information print
(Executable only when the FAX is installed.)
24 FAST SRAM clear
(Executable only when the FAX is installed.)
30 TEL/LIU status change check
(Executable only when the FAX is installed.)
33 Signal detection check
(Executable only when the FAX is installed.)
34 Communication time measurement
(Executable only when the FAX is installed.)
37 Speaker sound volume setting
(Executable only when the FAX is installed.)
38 Time setting/check
(Executable only when the FAX is installed.)
Main
code Sub
code
Contents