Toshiba E-studio 556 Troubleshooting Manual Download Page 94 | Manualshive

Page: 94 / 104

background image

7 CHECKING THE EQUIPMENT STATUS WITH TopAccess

92 Error Codes

2E11

Not enough memory

Wait for a while and try again. If the error still persists,
turn the power OFF and then back ON, and make
another effort.

2E14

Invalid parameter specified

If you are using a template, create it again. If the error
still persists, turn the power OFF and then back ON,
and then try again.

2E15

Exceeding maximum file capacity

Divide the file into several files, or reattempt in a single-
page format.

2E30

Failure to create directory

Make sure that the access privilege to the storage
directory is writable and also that the disk in the
directory has enough space, and then try again. If more
than one job is performed simultaneously, the error may
occur because the disk temporarily runs out of space. In
this case, wait for a while and try again. If the error still
persists, turn the power OFF and then back ON, and
make another effort.

2E31, 2E33

Failure to create file

Make sure that the access privilege to the storage
directory is writable and also that the disk in the
directory has enough space, and then try again. If more
than one job is performed simultaneously, the error may
occur because the disk temporarily runs out of space. In
this case, wait for a while and try again. If the error still
persists, turn the power OFF and then back ON, and
make another effort.

2E32

Failure to delete file

Turn the power OFF and then back ON. Try the
problem job again. If the error still persists, contact your
service representative.

2E40

Failure to convert image file format

This error occurs when conversion to a highly
compressed PDF format fails. Do the scanning again. If
the error still persists, Use the normal PDF format.
When this error occurs in conversion other than to a
highly compressed PDF format, turn the power OFF
and then back ON. Then try to scan again. If the error
still persists, contact your service representative.

2E43

Encryption error. Failure to create a file

If the error still persists after reattempting, turn the
power OFF and then back ON. Then make another
effort.

2E44

Creating a file was not allowed

Creating an unencrypted file was not allowed.
Configure the encryption settings and try again. To
create an unencrypted file, consult the administrator.

2E45

Failure in making meta data

Make sure that the template setting is correct, and do
the scanning again. If the error still persists, turn the
power OFF and then back ON, and then try again.

2E65

There are too many documents in the folder. Failure in
creating a new document

Delete the data in the local storage folder in the
equipment and try scanning again.

2E66

HDD full failure during processing

Reduce the number of pages of the problem job and try
again. Check whether the server or local disk has
sufficient space in its capacity.

2EC0

Job canceled

The job was canceled.

2EC1

Power failure occurred

Make sure that the power cable is connected properly
and is inserted securely. Resend the job.

Remote Scan, WS Scan, File Downloader

2A20

Failure to acquire resource

Reattempt the problem job. If the error still persists, turn
the power OFF and then back ON, and make another
effort.

2A31

WS Scan function is not available

Check if the WS Scan function is enabled. If not,
change it to “enabled”.

2A40

System fatal error

Turn the power OFF and then back ON. Try scanning
again.

2A50

Job canceled.

The job was canceled.

2A51

Power failure occurred

Make sure that the power cable is connected properly
and is inserted securely. Resend the job.

Error Code

Problem Description

Corrective Action

«
...
92
93
94
95
96
...
»

Summary of Contents for E-studio 556









































































































Reviews:

No comments

Related manuals for E-studio 556

Brand: TASKalfa Pages: 36

imagePROGRAF GP-540

Brand: Canon Pages: 82

4150S - WorkCentre B/W Laser

Brand: Xerox Pages: 4

Brand: Geeetech Pages: 52

ECOSYS FS-C5350DN

Brand: Kyocera Pages: 178

Brand: Kyocera Pages: 44

Brand: DataMetrics Pages: 35

Brand: DataMetrics Pages: 37

Brand: WOOSIM Pages: 27

Brand: Sharp Pages: 2

Brand: Sharp Pages: 1

Brand: Sharp Pages: 62

Brand: Sharp Pages: 62

Brand: Sharp Pages: 306

Brand: Sharp Pages: 4

Brand: Sharp Pages: 837

Brand: Sharp Pages: 836

BIZHUB PRO C6500

Brand: Konica Minolta Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands