manualshive.com logo in svg

Toshiba E-studio 556, Troubleshooting Manual

The Toshiba E-studio 556 is a multifunctional printer that offers efficient and high-quality printing, scanning, and copying capabilities. For a hassle-free setup and operation, make sure to download the Quick Start Manual, available for free download at manualshive.com. With this comprehensive manual, you can quickly learn how to maximize the features of your Toshiba E-studio 556. So, get your manual now and start enjoying the full potential of this exceptional printer.

Share
Download
background image

7 CHECKING THE EQUIPMENT STATUS WITH TopAccess

90    Error Codes

2C44

Creating a file was not allowed

Creating an unencrypted file was not allowed. 
Configure the encryption settings and try again. To 
create an unencrypted file, consult the administrator.

2C45

Failure in making meta data

Make sure that the template setting is correct, and do 
the scanning again. If the error still persists, turn the 
power OFF and then back ON, and then try again.

2C60

HDD full failure during processing

Reduce the number of pages of the problem job and try 
again. Check whether the server or local disk has 
sufficient space in its capacity.

2C61

Failure to read Address Book

Turn the power OFF and then back ON. Try the 
problem job again. Reset the data in the Address Book 
and reattempt it. If the error still persists, contact your 
service representative.

2C63

Terminal IP address unset

Ask your administrator to set the IP address of the 
equipment.

2C64

Terminal mail address unset

Ask your administrator to set the Email address of the 
equipment.

2C65, 2C66, 

2C69

Failure to connect to SMTP server

Make sure that the SMTP server is correctly working or 
the SMTP server address has been set correctly.

2C6A

Failure to send Email message

Turn the power OFF and then back ON. Try scanning 
again. If the error still persists, contact your service 
representative.

2C6B

Invalid address specified in From: field

Ask your administrator to check the SMTP 
Authentication method or if there is an unpermitted 
character in the Terminal mail address. Set the correct 
SMTP Authentication method or delete the unpermitted 
character in the Terminal mail address.

2C6C

Invalid address specified in To: field

Make sure that there is no unpermitted character in the 
Destination mail address. Delete any unpermitted 
character and reset the appropriate Destination mail 
address, then try again.

2C70

SMTP service is not available

Ask your administrator whether the SMTP service is 
enabled.

2C71

SMTP authentication error

Confirm that the login name and password are correct. 
If SSL is enabled, make sure that the SSL port number 
is correctly set.

2C72

POP Before SMTP error

Confirm that the POP Before SMTP settings and POP3 
settings are correct.

2CC0

Job canceled

The job was canceled.

2CC1

Power failure occurred

Make sure that the power cable is connected properly 
and is inserted securely. Resend the job.

Save as File

2D10, 2D12, 

2D13

Wrong Job status

Turn the power OFF and then back ON. Try it again. If 
the error still persists, contact your service 
representative.

2D11

Not enough memory

Wait for a while and try again. If the error still persists, 
turn the power OFF and then back ON, and make 
another effort.

2D14

Invalid parameter specified

If you are using a template, create it again. If the error 
still persists, turn the power OFF and then back ON, 
and then try again.

2D15

Exceeding maximum file capacity

Divide the file into several files, or try again in a single-
page format.

2D30

Failure to create directory

Make sure that the access privilege to the storage 
directory is writable and also that the disk in the 
directory has enough space, and then try again. If more 
than one job is performed simultaneously, the error may 
occur because the disk temporarily runs out of space. In 
this case, wait for a while and try again. If the error still 
persists, turn the power OFF and then back ON, and 
make another effort.

Error Code

Problem Description

Corrective Action

Summary of Contents for E-studio 556









































































































Reviews:

No comments

Related manuals for E-studio 556

Canon IMAGERUNNER ADVANCE C5051 Quick Reference preview
IMAGERUNNER ADVANCE C5051
Brand: Canon Pages: 72
Canon iPF710 - imagePROGRAF Color Inkjet Printer Manual preview
iPF710 - imagePROGRAF Color Inkjet Printer
Brand: Canon Pages: 92
Canon iPF8000S - imagePROGRAF Color Inkjet Printer Brochure preview
iPF8000S - imagePROGRAF Color Inkjet Printer
Brand: Canon Pages: 8
Canon imageRUNNER ADVANCE C9075S PRO Safety Instructions preview
imageRUNNER ADVANCE C9075S PRO
Brand: Canon Pages: 48
Canon IMAGERUNNER 7095 PRINTER Service Manual preview
IMAGERUNNER 7095 PRINTER
Brand: Canon Pages: 615
Canon imageRUNNER C3125i User Manual preview
imageRUNNER C3125i
Brand: Canon Pages: 816
TallyGenicom 7006 Quick Start Manual preview
7006
Brand: TallyGenicom Pages: 2
Oce COLOR SYSTEM 110 Operator'S Manual preview
COLOR SYSTEM 110
Brand: Oce Pages: 392
IDStation fastID User Manual preview
fastID
Brand: IDStation Pages: 18
Oce VarioLink 3622 User Manual preview
VarioLink 3622
Brand: Oce Pages: 209
Oki C7500n Maintenance Manual preview
C7500n
Brand: Oki Pages: 192
Oki LP470s Manual Rapide preview
LP470s
Brand: Oki Pages: 140
Ricoh Pro L5130e Settings Manual preview
Pro L5130e
Brand: Ricoh Pages: 44
Xerox DocuPrint C6 User Manual preview
DocuPrint C6
Brand: Xerox Pages: 78
Oki MC561 Maintenance Manual preview
MC561
Brand: Oki Pages: 276
Brightek U04 Quick Install Manual preview
U04
Brand: Brightek Pages: 8
Lexmark MS310d Quick Refence Manual preview
MS310d
Brand: Lexmark Pages: 79
Oki ES8473 Maintenance Manual preview
ES8473
Brand: Oki Pages: 271

Brands by name

Popular brands

Load more brands