Toshiba E-studio 556 Troubleshooting Manual Download Page 17

Page: 17 / 104

1.TROUBLESHOOTING FOR THE HARDWARE

Clearing a Paper Misfeed 15

1 TROUBLESHOOTING FOR THE HARDWARE

If paper misfeeds occur frequently

The following are the common causes of paper misfeeds. If the problem persists, check for the following situations.

An unsuitable original is placed on the Reversing Automatic Document Feeder.

Unavailable paper with the equipment is used.

Paper sizes are not consistent between the size in a drawer or the bypass tray and the size registered in the
equipment.

All the misfed paper has not been removed.

There is too little or too much of a gap between the paper and the side guide in the drawer.

The amount of paper placed in a drawer exceeds the limit indicated on the side guide of the drawer.

Paper misfeed in the Reversing Automatic Document Feeder (Lower)

Do not touch the transfer belt.

Do not touch the transfer belt when removing the paper misfed inside the
equipment. Doing so may cause damage on the equipment or result in a
poor output.

Open the Reversing Automatic Document Feeder.

Open the reverse cover by pushing the green lever
and remove the original.

Push the green portion and close the reverse cover.

Summary of Contents for E-studio 556








































































































Search results

Summary of Contents for E-studio 556

Reviews:

Related manuals for E-studio 556

Brands by name

Popular brands

Toshiba E-studio 556, Troubleshooting Manual

Search results

Summary of Contents for E-studio 556

Reviews:

Related manuals for E-studio 556

Brands by name

Popular brands