Toshiba AJ65VBTCU-68ADIN User Manual Download Page 94

Page: 94 / 106

6 - 2 6 - 2

MELSEC-A

6 TROUBLESHOOTING

6.2 Using the LED Indications to Check Errors

This section explains how to check errors using the LED indications of the

AJ65VBTCU-68ADVN/ADIN.

Refer to the PLC CPU and master module user's manual for issues regarding the PLC

CPU and master module.

(1) When the AJ65VBTCU-68ADVN/ADIN "POWER" LED is off

Check item

Corrective action

Is 24VDC power on?

Check the external power supply.

Is the voltage of the 24VDC power supply within the

specified value?

Set the voltage value to within the range 20.4 to

26.4V.

(2) When the AJ65VBTCU-68ADVN/ADIN "RUN" LED is flashing

Check item

Corrective action

When used as the ver. 1

remote device station (ver.

1 compatible slave station)

1. Check that the mode select switch is not set to

other than 0. (When the module is used as the

ver. 1 remote device station, set the mode select

switch to "0".)

2. Check the error code (RWrn+8) to confirm the

channel where the input range setting error

occurred.

3. Correct the sequence program or GX Developer

setting.

Is the LED flickering

at 0.1s intervals in

the normal mode?

When used as the ver. 2

remote device station (ver.

2 compatible slave station)

1. Check that the mode select switch is not set to

other than 3. (When the module is used as the

ver. 2 remote device station, set the mode select

switch to "3".)

2. Check the error code (RWrn+8) to confirm the

channel where the input range setting error

occurred.

3. Correct the sequence program or GX Developer

setting.

Is the LED flickering at 0.5s intervals in the mormal

mode?

1. Check that the mode select switch has not been

moved from the position at power-on. (When the

switch is returned to the original setting, the

flickering LED is lit.)

2. Check the error code (RWrn+8) to confirm the

channel where the average number of times

setting or average time setting error occurred.

3. Correct the sequence program or GX Developer

setting.

Is the LED flickering at 0.1s intervals in the test

mode?

Check that the mode select switch is not outside the

setting range.

Is the LED flickering at 0.5s intervals in the test

mode?

Change the offset/gain adjustment to within the

available setting range.

Summary of Contents for AJ65VBTCU-68ADIN











































































































Search results

Summary of Contents for AJ65VBTCU-68ADIN

Reviews:

Related manuals for AJ65VBTCU-68ADIN

Brands by name

Popular brands

Toshiba AJ65VBTCU-68ADIN, User Manual

Search results

Summary of Contents for AJ65VBTCU-68ADIN

Reviews:

Related manuals for AJ65VBTCU-68ADIN

Brands by name

Popular brands