manualshive.com logo in svg

Tornatech GPU, Installation And Maintenance Manual, Page: 56 / 67

Share
Download
Tornatech GPU Installation And Maintenance Manual Download Page 56

 

 

56 

 

The Statistics 

First/Last Service Statistics 

History > Statistics since first/last service 

 

 

The following description applies to two pages, reachable by the “First Service Statistics” and the “Last Service 
Statistics” button on the History page. All statistics shown here are calculated since the first/last service was done. 
All dates are in the YYYY.MM.DD format and all time references are in the HH:MM:SS format.  
 
-Since: Date and time when the first/last service was done. 
-On Time: Total duration of controller powered on during that period. 
 
Motor:  
-

Last run: Date and time of the motor’s last run.  

-Run time: Total running time of the motor during that period. 
-Start count: Number of times the motor started during that period. 
 
Pressure: 
-Minimum: Value of minimum pressure displayed in the system actual unit and the moment it was reached.  
-Maximum: Value of maximum pressure displayed in the system actual unit and the moment it was reached.  
-Average: Calculated value of the average pressure during that period displayed in the system actual unit.  
 
Temperature: 
-Minimum: Value of minimum temperature displayed in the system actual unit and the moment it was reached.  

Summary of Contents for GPU




































































Reviews:

No comments