manualshive.com logo in svg

Tornatech GPU, Installation And Maintenance Manual, Page: 22 / 67

Share
Download
Tornatech GPU Installation And Maintenance Manual Download Page 22

 

 

22 

 

R: Ethernet connector 
S: K-Type Thermocouple connector 
T: Alarm Bell connector 

 

Warning 
After 2 years of service, the Vizitouch battery may become less efficient and could lose the time after a shutdown. 

 

Alarm Bell 

The alarm bell is activated under default faulty conditions and under optional or user defined conditions. 
 
Any of these conditions will energize the alarm bell but may be silenced, except in some cases, by pressing on the 
“Alarms / silence” membrane button. When silenced, the alarm bell restarts ringing if a new fault occurs or if the 
alarm conditions remain unchanged after 24 hours. The alarm bell automatically stops ringing if alarm conditions 
are not present anymore. 
 
Note: other external conditions may trigger optional conditions depending of the factory settings. Verify drawings 
affixed inside the cabinet. 
 
Default Conditions : 
- IO Cards Communication Loss 
- CAN System Failure 
- File System Failure 
- Alternate Isolating Switch / Circuit Breaker Off / Tripped* 
 

First Setup 

The First Setup must be done prior to using the controller. Completing the First Setup is the only way to access the 
homepage and enable the automatic mode of the controller. 

 

 

Summary of Contents for GPU




































































Reviews:

No comments