manualshive.com logo in svg

Tornatech GPU, Installation And Maintenance Manual, Page: 24 / 67

Share
Download
Tornatech GPU Installation And Maintenance Manual Download Page 24

 

 

24 

 

I: The alarm/warning notification. 
Warning indicator: Exclamation mark in a yellow round icon. If no alarm is in ACTIVE condition on the controller and 
at least one warning is ACTIVE or OCCURRED, the warning indicator will be present.  
 
Alarm indicator: Exclamation mark in a red triangle icon. As soon as at least one alarm is ACTIVE or OCCURRED, 
the alarm indicator will be flashing. 
  
J: The motor configuration symbol shows how the motor is wired to the contactor(s). This symbol is used to show if 
the motor is in a starting configuration (Wye wiring, for example) or in a permanent running configuration (i.e. delta 
wiring) 
 

Permanent delta motor connection. 

 

Temporary wye motor connection. 

 

Temporary auto-transformer motor connection. 

 

Temporary primary resistor motor connection. 

 

Temporary solid state starter motor connection. 

 

Temporary part-winding motor connection. 

 
K: Representation of the motor starting or stopping cause. A green capsule will indicate the reason why the motor is 
running. Possible choices are: 
 
EMERGENCY: Manual motor starting activated by the emergency handle.  
 
MANUAL: Manual motor starting activated by the START push button.  
 
REMOTE MANUAL: Manual motor starting activated by a remote start contact.  
 
DELUGE: Automatic motor starting activated by a deluge valve. 
 
AUTO: Automatic motor starting activated by pressure drop  
 
REMOTE AUTO: Automatic motor starting activated by remote equipment 
 
FLOW: Automatic motor starting activated by a signal in the FLOW/ZONE START/STOP input.  
 
HIGH ZONE: Automatic motor starting activated by a signal in the FLOW/ZONE START/STOP input.  
 
WEEK TEST: Automatic motor starting activated by a scheduled test. 
 
MANUAL TEST: Automatic motor starting activated by the run test push button. 
 
 
A red capsule will indicate the reason why the motor is not running despite the fact that a request is being made. 
Possible choices are: 
 
LOAD SHED: The transfer switch has transferred to the alternate position and the motor starting is delayed to 
reduce the load on the alternate power source. This functionality is optional. 

Summary of Contents for GPU




































































Reviews:

No comments