TOPP C15 Series Installation And Use Instructions Manual Download Page 14

Page: 14 / 24

3.6

PACKAGE

Each package of the product (cardboard box) contains

(Fig. 3):

•No. 1 Actuator equipped with power supply cable;
•No. 1 Window frame connection bracket (

Ref.A

);

•No. 2 Frontal support standard brackets

(Ref. C);

•No. 1 Bracket for bottom hung opening

(Ref. B);

•No. 1 Drilling template;
•No. 1 Installation and use instructions;
•No. 1 Safety plate

(fig. 4).

Make sure that the above described components

are contained in the package, as well as that the
actuator has not been damaged during transport.

Should any anomaly be detected, it is forbidden to

install the actuator, and it is compulsory to require
technical assistance from your dealer or the
manufacturer.

The packaging (paper, plastic, etc.) has to be

disposed according to the laws in force.

SAFETY

Operators must be informed of accident risks,

safety devices and the general accident prevention
regulations established by international directives
and by the law in force in the countryof use.

All operators must strictly comply with the

accident prevention regulations in force in the
country of use.

During handling and installation of the parts,

the personnel shall be equipped with suitable
personal protection equipment (PPE) so as to
perform the works required under safe conditions.

Do not remove or alter the plates placed on the

actuator by the manufacturer.

If the window frame is accessible from or installed

at a height of less than 2.5 m from the ground, and if it
can be commanded by an untrained user or with a
remote control device, fit an emergency stop system
which automatically cuts in to prevent the risk of
crushing or dragging parts of the body inserted
between the moving and fixed parts of the window
frame.

Any tampering with or unauthorised replacement

of one or more parts or components of the actuator,
o r t h e u s e o f u n o r i g i n a l a c c e s s o r i e s a n d
consumables, may increase the risk of accident and
thus relieves the manufacturer of all civil and
penalliability.

E x t r a o r d i n a r y a n d r o u t i n e m a i n t e n a n c e

operations involving the total or partial dismounting
of the actuator may only be performed after
disconnecting it from the power supply.

This appliance may not be used by persons

(children included) with reduced physical, sensorial
or mental capacities, or inexpert people, unless they
are supervised and taught how to use it by a person
responsible for their safety.

Children must be controlled to make sure they do

not play with the appliance.

4.1

GENERAL INSTRUCTIONS

4.2

SAFETYDEVICES AGAINST ELECTRIC
HAZARD

The actuator is protected against electric hazard due to
direct and indirect contacts.
The protection measures against direct contacts aim at
protecting  people  against  hazards  due  to  contact  with
active  parts,  usually  live  parts;  while  the  protection
measures  against  indirect  contacts  aim  at  protecting
people against hazards due to conducing part, which are
usually insulated, but could become live in case of failure
(insulation failure).
The adopted protection measures are the following:

Insulation of live parts by means of a plastic material

body;

Enclosure with suitable protection degree;

Only for Mod. C20/230 V equipped with double

insulation

: Protection of passive type given by the use

of components with double insulation, also called
components of class II or with equivalent insulation.

4.3

SAFETY PLATES

It is forbidden to remove, move, spoil or in anyway
reduce the visibility of the safety plates. Failure to
observe the above may cause serious harm to
people and damage to property. The manufacturer
declines all liability for any damage caused by the
failure to observe the above requirement.
Fig. 4

illustrates the safety plate: this must applied

directly to the outside of the actuator or near it and
always in a position where it can be seen by the installer
and/or operator.

INSTALLATION AND USE INSTRUCTIONS

C15

It is strictly forbidden to use the actuator for

improper uses other than the one foreseen bythe
manufacturer (see par. 3.4).

It is strictly forbidden to install the actuator on the

external side of the window frame subject to
atmospheric agents (rain, snow, etc.).

The use of the actuator in environments with

potentially explosive atmosphere is strictly
forbidden.

It is compulsory to keep the package and the

actuator out of reach of children.

Check carefully all environmental conditions

(temperature,  humidity,  wind,  snow,  potential
chemical  agents,  etc.)  and  installation  settings
(misaligned fitting of brackets and attachment to the
frame, frictions produced by hinges or gaskets, use
o f   s e l f b a l a n c i n g   w i n d o w   s t a y s ,   e t c . )   i t   i s
recommended  that  they  not  exceed  the  actuator
performances shown in the technical table.