background image

POLE HEDGE TRIMMER 400W  TTB427GTM

NOTE:

 The lower adjustable section is NOT to increase the 

cutting length but to alter the harness positions.

6. CUTTING ANGLE ADJUSTMENT

WARNING! Always  switch  the  motor  off  and 

pull the mains plug from power supply before 

any adjustment.

This  pole  hedge  trimmer  supplied  4  cutting  position  for 
different cutting status, adjust the cutting head angle to fit the 
growth of the plant.
1).  Push  lock-off  buttons  (2)  on  the  left  and  right  of  the 
trimming head. (See Fig. 4a).

 

2). Adjust the head until it snaps securely into place at one of 
the four positions indicated by the notches. (See Fig. 4b).
     

7. STARTING AND STOPPING

1). STARTING

The pole hedge trimmer is fitted with a lock-off button feature. 
To start the pole hedge trimmer, simply pull the lock-off button 
(8) and hold it in position then fully press and hold the switch 
trigger (9) to switch the product on. (See Fig.5a)

NOTE:

 It is not necessary to maintain pressure on the lock-

off button once the switch trigger is squeezed and the motor 
is  running. The  lock-off  button  is  a  safety  device  to  avoid 
accidental start-up of the device.

Fig. 4a

0

º

-45

º

45

º

90

º

PIVOT

BUTTON

Fig. 4b

Fig. 5a

STEP 1

STEP 2

400w 高枝.indd   18

12-3-2   上午11:36

Summary of Contents for TTB427GTM



























Reviews: