background image

© Titan Tool Inc.  All rights reserved. 

7

Pressure Relief Procedure

Be sure to follow the pressure relief procedure 

when shutting the unit down for any purpose, 

including servicing or adjusting any part of the 

spray system, changing or cleaning spray tips, or 

preparing for cleanup.

  1.  Lock the gun by turning the gun trigger lock to the locked 

position.

  2.  Turn off the sprayer by moving the sprayer ON/OFF switch 

to the OFF position.

  3.  Unlock the gun by turning the gun 

trigger lock to the unlocked position.

  4.  Hold the metal part of the gun firmly to 

the side of a metal container to ground 

the gun and avoid a build up of static 

electricity.

  5.  Trigger the gun to remove any pressure that may still be in 

the hose.

  6.  Lock the gun by turning the gun trigger lock to the locked 

position.

  7.  Move the PRIME/SPRAY valve down to the PRIME 

position.

Spraying

NOTE:   When spraying block filler, mastics or high solid 

coating, remove the gun filter and high pressure 

filter screens.

Spraying Technique

The key to a good paint job is an even coating over the entire 

surface.  This is done by using even strokes.  Keep your arm 

moving at a constant speed and keep the spray gun at a constant 

distance from the surface.  The best spraying distance is 10 to 12 

inches between the spray tip and the surface.

Keep stroke smooth and at an even speed.

Even coat throughout

Approximately

10 to 12 inches

Keep the spray gun at right angles to the surface.  This means 

moving your entire arm back and forth rather than just flexing 

your wrist.

Heavy Coat

Do not flex wrist while spraying.

Light Coat

Light Coat

Keep the spray gun perpendicular to the surface, otherwise one 

end of the pattern will be thicker than the other.

Approximately

10 to 12 inches

Right way

Wrong way

The spray gun should be triggered by turning it on and off with 

each stroke.  This will save paint and avoid paint buildup at 

the end of the stroke.  Do not trigger the gun during the middle 

of a stroke.  This will result in an uneven spray and splotchy 

coverage.

Proper way to trigger the spray gun

Approximately

10 to 12 inches

Keep stroke

even

Start stroke

End stroke

Pull trigger

Release trigger

Keep steady

Overlap each stroke by about 30%. This will ensure an even 

coating.

When you stop painting, lock the gun trigger lock, turn the 

pressure control knob counterclockwise to its lowest setting and 

set the PRIME/SPRAY valve to PRIME.  Turn the motor switch to 

OFF and unplug the sprayer.

Practice

  1.  Be sure that the paint hose is free of kinks and clear of 

objects with sharp cutting edges.

  2.  Turn the pressure control knob counterclockwise to its to 

its lowest setting.

  3.  Move the PRIME/SPRAY valve to the SPRAY position.

  4.  Turn the pressure control knob clockwise to its highest 

setting.  The paint hose should stiffen as paint begins to 

flow through it.

  5.  Unlock the gun trigger lock.

  6.  Trigger the spray gun to bleed air out of the hose.

  7.  When paint reaches the spray tip, spray a test area to 

check the spray pattern.

Good spray pattern

Paint tailing pattern

  8.  Use the lowest pressure 

setting necessary to get a 

good spray pattern.  If the 

pressure is set too high, the 

spray pattern will be too light.  

If the pressure is set too low, 

tailing will appear or the paint 

will spatter out in gobs rather 

than in a fine spray.

Summary of Contents for Advantage GPX 220





























Reviews: