Timberwolf TW PTO/S426 Instruction Manual Download Page 28

Page: 28 / 49

TW PTO S426

25 / 45

DECALS

24.06.2019

Danger.

Do not operate without this

cover in place.

Danger.

Rotating blades inside.

Stop engine and remove key

before removing discharge unit.

Relays -

Forward latch,

Engine safety

Caution.

When transporting, discharge

clamps may work loose.Check

frequently.

Caution.

Avoid standing directly in front of

feed funnel to reduce exposure

to noise, dust and risk from

ejected particles.

Danger.

Do not use this machine without

the discharge unit fitted. failure

to comply may result in serious

inury or damage.

Danger.

Ensure machine is on level

surface before detaching from

the tractor PTO shaft and 3-point

linkage.

Danger.

Autofeed system fitted.

Rollers may turn without

warning! When the engine is

switched off the rollers will turn

during the run down period.

Do not exceed 1000RPM.

Danger.

Ensure machine is secure to 3 -

point linkage of the tractor

before operation.

P637

P655

P653

P654

P656

Decal Description

3004 2998 1363 18483 18795 1136

119

Aeq

PTO S426

SHREDDER

TIMBERWOLF

P650

2438

19332

19343

P1810

P1811

Summary of Contents for TW PTO/S426


















































Search results

Summary of Contents for TW PTO/S426

Reviews:

Related manuals for TW PTO/S426

Brands by name

Popular brands

Timberwolf TW PTO/S426, Instruction Manual

Search results

Summary of Contents for TW PTO/S426

Reviews:

Related manuals for TW PTO/S426

Brands by name

Popular brands