TW 280TVGTR
8 / 73
OPERATING INSTRUCTIONS
C190-0176
01.03.2019
Rev: 2.0
TW 280TVGTR, Tracked Hydraulic Fed Chipper, 45hp 1498cc Diesel Engine
Declared vibration emission value in accordance with BS EN 12096:1997
Whole Body Vibrations (m/s
2
)
Hand Arm Vibrations (m/s
2
)
Measured vibration
emission value
a
1.55
4.55
Uncertainty
K*
0.62
2.28
Values determined when standing on driver’s platform tracking over soft grassy ground.
Measured vibration
emission value
a
1.80
5.05
Uncertainty
K*
0.72
2.02
Values determined when standing on driver’s platform tracking over hard paved ground.
*K
value calculated according to provisions in BS EN 12096:1997
VIBRATION DATA
This data is provided to enable assessment of vibration exposure, when the machine is operated in the modes described.
Please refer to local Health & Safety Regulations to determine the daily exposure action and limit values.
RECOMMISSIONING AFTER STORAGE
Ensure machine is stable.
•
Remove all guards and check all fasteners. If necessary,
•
retighten as described within this manual.
Ensure discharge tube is correctly fastened, free of
•
objects or blockages and rotates around its pivot
without being directed to face the point of operation
(danger zone).
Ensure feed funnel is free from foreign objects e.g. tools
•
and clothing.
Lower and raise feed funnel into its open and closed
•
positions to confirm functionality.
Check fuel and hydraulic fluid levels within engine and
•
reservoir and top up accordingly. *
Inspect all internal parts e.g. drive belts, taper locks and
•
shaft keyways.
Check belt tension as described within this manual.
•
Inspect cutting blades to confirm they are sharp and
•
suitable for use.
Re-connect the battery to its positive and negative
•
terminals.
Undertake electrical diagnostic continuity check, to
•
confirm circuit is complete.
Re-lubricate all grease pipes. Remove pipes and bleed
•
the system prior to use, if necessary. *
Follow daily checks before starting, as described within
•
this manual.
Start the machine.
•
Run for 15 minutes at half throttle, prior to any cutting
•
activity, to clear the combustion engine. Once
complete, bring the machine onto full throttle for a
further 5 minutes.
*Storage fluids should be replaced, DO NOT USE old
stagnate fluids.
Summary of Contents for TW 280TVGTR
