background image

04/03/2015

 

Orion - Gulliver

 

User Manual 

 

 

18

 

 

   

 

9.

 

Malfunctions 

 
The  Table  below  lists  the  problems  which  could  occur  during  the  machine's  working  life.  The 

possible cause of  each problem  is indicated  along  with the relative action required  to resolve the 
situation. 

Do not perform any actions which are reserved for authorised service personnel. 

 

PROBLEM 

ACTION 

THE PLATFORM LIFT MAY BE 

USED 

The Platform Lift does not respond to 

commands 

Check that the load does not exceed its maximum 

limit 

Check that all floor doors are closed 

Lack of power supply. Check that the switch 

located on the electrical panel’s door is turned ON 

The emergency stop button located inside the 

cabin has been pressed. Unlock it by turning it 

clockwise to make it return to its normal position 

If the problem persists request technical 

assistance 

Floor signal not functioning 

request technical assistance 

YES 

The platform lift does not respond to 

commands from the floor. 

Check and verify that the platform lift is stopped at 

a floor.  If it is not, an educated person can have 

the platform descend to the next lower floor and 

try again. 

Cabin light not functioning 

request technical assistance 

YES 

Incorrect floor levelling (the Platform 
Lift stops and is not aligned with the 

floor) 

Turn the switch located on the electrical panel’s 

door to the OFF position and request technical 

assistance 

NO 

When the Platform Lift is stopped at 

the floor, the door does not unlock 

Turn the switch located on the electrical panel’s 

door to the OFF position and request technical 

assistance 

NO 

When the Platform Lift is not yet at the 

floor, the door is unlocked 

Turn the switch located on the electrical panel’s 

door to the OFF position and ask for assistance 

from service assistance and mechanically block 

the unlocked door. 

NO 

The machine presents malfunctions 

such as jolts, vibrations and similar 

behaviour 

Turn the switch located on the electrical panel’s 

door to the OFF position and request technical 

assistance 

NO 

Telephone device (fixed line) - 

Emergency call not made. 

Verify that the telephone line has been connected 

and request assistance if necessary. 

NO 

 

Telephone auto-dial (fixed or GSM 

line) - Emergency call not made. 

Verify that the telephone line has been connected 

or, in the case of GSM, verify that the SIM card is 

active. Request assistance if necessary. 

NO 

 

When the user interrupts the machine’s function (in the above mentioned ways), he/she is obliged 
to affix notices regarding the machine's status near every access.

 

Summary of Contents for gulliver

























Reviews: