![background image](http://html1.mh-extra.com/html/thyssenkrupp/drive-dab530/drive-dab530_operating-manual_1113962083.webp)
MSK110TH
+ MB100
Datum 24.09.2009
Art.Nr. 85210
Änd. Stand 271/09
7
viewing side=
plug-in side
plug pin
5. Commissioning
Following proper installation and wiring, the
measuring system can be commissioned by
switching on the supply voltage. After switching
on, the device initializes itself independently.
6. Output signals
The translation module translates the length
information of the magnetic sensor into incre-
mental output signals with real-time processing of
the output signals.
Please note that pulses having the width of
the pulse interval set can occur at standstill of
the device
(caused by the internal interpolation
method).
Caution!
When dimensioning the follow-on elec-
tronics please take care that it is adjusted to the
set pulse interval or counting frequency, respec-
tively.
Signal sequence
connection of the screen and earth is made to
a large surface area with a sound connection to
minimise impedance.
The system should be positioned well away from
cables with interference; if necessary
a protective
screen or metal housing
must be provided. The
running of wiring parallel to the mains supply
should be avoided.
Contactor coils must be linked with spark sup-
pression.
Supply voltage
The voltages depend on the sensor designs; they
are to be taken from the delivery documentation
and the identification plate.
e.g.:
4,5VDC ... 5,5VDC
Attention!
When connecting sensor and follower
electronics, please do not exceed the max. admis-
sable cable length.
4.1 Connection note acc. to RS422 standard
Please provide the channels with a 120 Ohm ter-
minating resistor.
•
•
4.2 Connection type
E2X:
Connection with 12 pole coupler plug.
Pin
Signal
1
B
2
- - -
3
/A
4
A
5
- - -
6
- - -
7
- - -
8
/B
9
- - -
10
+UB
11
- - -
12
GND
7. Maintenance
We recommend cleaning the magnetic strip’s surface
from time to time with a soft rag. This avoids dirt
(dust, chips, humidity ...) sticking to the strip.
8. Trouble shooting
Below are some typical errors which may occur du-
ring installation and operation:
Magnetic strip incorrectly mounted (active sur-
face must be mounted towards the sensor) (see
chapter 3.1).
Use of foreign protective strip. Must always be
non-magnetic.
Sensor not or incorrectly connected (pin connec-
tion, see chapter 4.2).
Tolerance for the gap between magnetic sensor and
magnetic strip not observed over the total travel
distance. Sensor touches strip (see fig. 6).
Cable squeezed / interrupted / cut by sharp
edges.
Sensor’s active side not mounted towards the
magnetic strip (see fig. 6).
Sensor has not been aligned according to fig 6.
•
•
•
•
•
•
•
Summary of Contents for Drive DAB530
