Thomas 35DT Operator And Parts Manual Download Page 70

Page: 70 / 70

6. PARTS BREAKDOWN

6.8 ENGINE SPARE PARTS

ITEM

PART NO.

DESCRIPTION

QTY.

261

Hose, Fuel 5 5/16

4 ft.

407

Hose, Fuel 3 3/16

5 ft.

6268

Clamp, Hose #32

11141

Clamp, Hose #16

12052

Clamp, Hose 0.75

14797

Cock, Shut off 1/4 NPT MX 1/4 F

19949

Clamp, Fuel Line

26737

Clamp, Wire Hose 3/16

38558

Isolator, Engine

10.

49235

Engine, Assembly V1105

11.

49283

Clamp, Muffler 1 3/8” PL

12.

49424

Throttle, Control Assembly

13.

49478

Cleaner, Air Assembly 4”

with Safety Filter

14.

49454

Hose, Air Cleaner

15.

49463

Muffler, Mini Skid 1105

16.

49464

Pipe, Exhaust

17.

49016

Pump, Hyd. Assy. PLP 20/10

11.2CC/4.0CC

18.

49465

Tube, Filler Neck

19.

49468

Hose, Filler Neck

20.

964648

Motor Mount, LH

21.

964632

Motor Mount, RH

22.

964664

Frame Adapter, LH

23.

964663

Frame Adapter, RH

24.

49616

Starter

25.

39185

Alternator

26.

39186

Glow Plug

27.

43333

Air Cleaner, Primary

28.

49477

Air Cleaner, Safety

29.

43350

Engine Oil Filter

30.

49617

Fuel Filter

31.

964894

Throttle Cable Bracket

32.

38558

Isolator, Engine Mount

33.

49618

Stop Solenoid

34.

43345

Fan Belt

35.

49811

Hyd. Seal Kit, Tilt

36.

49875

Hyd. Seal Kit, Lift

https://www.tractormanualpdf.info/

Summary of Contents for 35DT







































































Search results

Summary of Contents for 35DT

Reviews:

Related manuals for 35DT

Brands by name

Popular brands

Thomas 35DT, Operator And Parts Manual

Search results

Summary of Contents for 35DT

Reviews:

Related manuals for 35DT

Brands by name

Popular brands