Thomas 35DT Operator And Parts Manual Download Page 55

Page: 55 / 70

6. PARTS BREAKDOWN

6.4 TRACKS

ITEM

PART NO.

DESCRIPTION

QTY.

965277

Axle Weld Assembly R.H.

965278

Axle Weld Assembly L.H.

964861

Front Hub Welded Assembly

51200

Bar, Drive Sprocket Washer

964859

Idler Mount Assembly, L.H.

964860

Idler Mount Assembly, R.H.

51193

Drive Sprocket

49339

Wheel, Polyolefin

1474

1/2” x 9” Bolt, Hex UNC

10.

49953

Conventional Rubber Track, Type G

11.

49492

Flange Bolt, 5/8” x 1 1/4”

12.

49955

Chain # 60H 62 Pitches, LH

12.

49954

Chain # 60H 50 Pitches, RH

13.

964548

Axle Welded Assembly

14.

964541

Axle Tower Welded Assembly

15.

51153

Plate, Front Idler

16.

964913

Bolt Cage Welded Assembly

17.

964952

Drive Sprocket

18.

964863

Plate

19.

51340

Bar, Spring Puller

20.

51339

Washer

21.

49407

Compression Spring

22.

49408

Nyloil Wear Pad

23.

51367

Wear Guide Support

24.

8613

1/2” Nylok Nut

25.

23385

1/2” Washer

26.

52035

Tensioner Block

27.

43559

1/2” Flange Nut

28.

3093

Nut, Wheel

29.

49501

1 1/2 “Set Screw

30.

49342

Wheel Stud, 1 7/8”

* - Item not shown.

https://www.tractormanualpdf.info/

Summary of Contents for 35DT







































































Search results

Summary of Contents for 35DT

Reviews:

Related manuals for 35DT

Brands by name

Popular brands

Thomas 35DT, Operator And Parts Manual

Search results

Summary of Contents for 35DT

Reviews:

Related manuals for 35DT

Brands by name

Popular brands