thomann LED-Commander 16/2 Page 43 User Manual Download

Page: 43 / 48

Proceed as follows to bring the firmware of the unit up to date. To do so, you need a com‐

pletely blank USB drive that is formatted with FAT32 format.
1.

Create a folder ‘led-commander16-2’ in the root directory of the USB drive.

Copy the file containing the current firmware version into the folder ‘led-

commander16-2’.

Connect a USB drive with the latest firmware version to the USB port of the device.

Turn the device off.

Keep the buttons

[PROGRAM

RECORD]

[MODE]

und pressed and turn the device on

again.

After two seconds, the display shows the message

‘Press any button

Update

firmware’

Press any key to start the firmware update.

After the installation is complete, the display shows the message

‘Update succeeded

Please reboot’

Then, turn off the device and after a few seconds turn it on again.

The unit will now start with the updated firmware.

Firmware update

Operation

LED-Commander 16/2

Summary of Contents for LED-Commander 16/2

















































Search results

Summary of Contents for LED-Commander 16/2

Reviews:

Related manuals for LED-Commander 16/2

Brands by name

Popular brands

thomann LED-Commander 16/2, User Manual

Search results

Summary of Contents for LED-Commander 16/2

Reviews:

Related manuals for LED-Commander 16/2

Brands by name

Popular brands