thomann LED-Commander 16/2 User Manual Download

Page: 14 / 48

1 FIXTURE

Buttons 1 to 16 to select the control channels. The corresponding indicator LED shows whether the respective

channel is activated (LED on) or deactivated (LED off).

2 SCENE

Eight buttons with double assignment for enabling / disabling of up to 16 scenes. The indicator LEDs show which

scenes are enabled (LED is on). Switching between the key groups (banks) 1…8 and 9…16 is done via the Shift key

(3).

3 Shift key SCENE

Button to toggle the SCENE buttons. The two indicator LEDs show which of the two key groups (banks) 1…8 (red) or

9…16 (green) is currently active.

4 CHASE

Eight buttons with double assignment for enabling / disabling of up to 16 chases. The indicator LEDs show which

chases are enabled (LED is on). Switching between the key groups (banks) 1…8 and 9…16 is done via the Shift key

(5).

Connections and operating elements

DMX-controller

Summary of Contents for LED-Commander 16/2

















































Search results

Summary of Contents for LED-Commander 16/2

Reviews:

Related manuals for LED-Commander 16/2

Brands by name

Popular brands

thomann LED-Commander 16/2, User Manual

Search results

Summary of Contents for LED-Commander 16/2

Reviews:

Related manuals for LED-Commander 16/2

Brands by name

Popular brands