thomann LED-Commander 16/2 Page 33 User Manual Download | Manualshive

Page: 33 / 48

background image

1.

Deselect all active FIXTURE, SCENE and CHASE channels (all blue LEDs off).

2.

Keep the button

[PROGRAM

½

RECORD]

pressed for three seconds to change to the oper‐

ating mode Programming/Recording.

3.

If needed, toggle between both memory banks ‘CHASE’ via the shift button.

4.

Press the

[TAP

½

DEL]

button and then the Chase button of the chase that you want to

delete.

5.

Keep the button

[PROGRAM

½

RECORD]

pressed for three seconds to exit the recording

mode.

Deleting a chase

Operation

LED-Commander 16/2

33

«
...
31
32
33
34
35
...
»

Summary of Contents for LED-Commander 16/2

















































Reviews:

No comments

Related manuals for LED-Commander 16/2

Brand: Raymarine Pages: 70

Brand: Harbor Freight Tools Pages: 4

Brand: Landoll Pages: 52

Brand: Gason Pages: 110

Brand: Gainsborough Pages: 2

Brand: Panlux Pages: 2

Brand: Haas Pages: 12

Brand: SaMASZ Pages: 25

Brand: MacDon Pages: 238

Brand: Salter Pages: 18

Brand: Salter Pages: 42

Brand: Salter Pages: 47

Brand: Salter Pages: 35

Brand: Salter Pages: 40

M-041 INDOOR CROSS

Brand: Salter Pages: 15

Brand: Mobiak Pages: 15

Brand: Gardol Pages: 80

Brand: MakAlon Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands