thomann LED-Commander 16/2 Page 26 User Manual Download | Manualshive

Page: 26 / 48

background image

Now, the channel RED of FIXTURE 01 can be controlled via the

[DIMMER]

control that

is assigned to the channel FIXTURE 01.

7.

Repeat steps 4 to 6 to allocate the remaining channels of FIXTURE 01.

The previously selected FIXTURE channel is displayed with the letter ‘M’ in the display.

In the example, this means that the

[DIMMER]

control that is assigned to channel FIXTURE 01

can control the maximum value of RED (CH 2).

Operation

DMX-controller

26

«
...
24
25
26
27
28
...
»

Summary of Contents for LED-Commander 16/2

















































Reviews:

No comments

Related manuals for LED-Commander 16/2

Brand: Modulate Pages: 2

Brand: AAON Pages: 36

Coronis 5MP Mammo

Brand: Barco Pages: 4

Brand: Barco Pages: 167

Color Coronis 2MP

Brand: Barco Pages: 156

Color Coronis 2MP

Brand: Barco Pages: 12

Brand: Barco Pages: 39

Brand: Barco Pages: 158

Brand: Danelec Pages: 67

Brand: Gatekeeper Pages: 8

Bure Rise & Go DB 56-309

Brand: Gate Pages: 8

Brand: Haag-Streit Pages: 18

Brand: Haag-Streit Pages: 20

Brand: V-TEK Pages: 2

Brand: V-TEK Pages: 112

Brand: RAPID REBOOT Pages: 18

Brand: MacDon Pages: 170

Brand: MacDon Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands