manualshive.com logo in svg

THine THCV242, Manual, Page: 41 / 53

Share
Download
THine THCV242 Manual Download Page 41

 

THCV242_ Rev.2.00_E 

Copyright

©

2019 THine Electronics, Inc.                                                                                                        THine Electronics, Inc. 

41/53 

Security E 

 

Internal Error / status signal monitoring register 

Internal error or status signal can be monitored as register read value. 

Error count register can be cleared by particular register write “1” access. 

 

Table 29.

 

Internal Error / status signal monitoring register 1/2 

 

 

Table 30.

 

Internal Error / status signal monitoring register 2/2 

 

 

 

 

 

Addr(h)

bit

Register Name

width

R/W

Description

Default

0x00F1

[7:1] reserved

7

-

-

-

[0]

R_SLINK_FBETERR_CLR

1

W

Sub-Link FieldBET error count clear
1: Clear

-

0x00F2

[7:0] R_SLINK_FBETERR_NUM_UP

8

R

Sub-Link FieldBET error count parameter

-

0x00F3

[7:0] R_SLINK_FBETERR_NUM_DN

8

R

Sub-Link FieldBET error count =256×R_SLINK_FBETERR_NUM_UP<7:0>

＋

R_SLINK_FBETERR_NUM_DN<7:0>

-

bit

Register Name

width

R/W

init

Description

0x17 4F

[7:4]

R_MLINK_CRC_ERRCLR

4

W

-

Main-Link CRC Error Counter Clear
1:Clear

[3:0]

R_MLINK_BET_ERRCLR

4

W

-

Main-Link BET Error Counter Clear
1:Clear

0x17 50

[7:0]

MLINK0_CRC_ERRNUM[15:8]

8

R

-

Main-Link(Lane0) CRC Error Number (Upper Byte)

0x17 51

[7:0]

MLINK0_CRC_ERRNUM[7:0]

8

R

-

Main-Link(Lane0) CRC Error Number (Low er Byte)

0x17 52

[7:0]

MLINK1_CRC_ERRNUM[15:8]

8

R

-

Main-Link(Lane1) CRC Error Number (Upper Byte)

0x17 53

[7:0]

MLINK1_CRC_ERRNUM[7:0]

8

R

-

Main-Link(Lane1) CRC Error Number (Low er Byte)

0x17 58

[7:0]

MLINK0_BET_ERRNUM[15:8]

8

R

-

Main-Link(Lane0) BET Error Number (Upper Byte)

0x17 59

[7:0]

MLINK0_BET_ERRNUM[7:0]

8

R

-

Main-Link(Lane0) BET Error Number (Low er Byte)

0x17 5A

[7:0]

MLINK1_BET_ERRNUM[15:8]

8

R

-

Main-Link(Lane1) BET Error Number (Upper Byte)

0x17 5B

[7:0]

MLINK1_BET_ERRNUM[7:0]

8

R

-

Main-Link(Lane1) BET Error Number (Low er Byte)

Adr

Summary of Contents for THCV242






















































Reviews:

No comments