manualshive.com logo in svg

THine THCV242, Manual, Page: 36 / 53

Share
Download
THine THCV242 Manual Download Page 36

 

THCV242_ Rev.2.00_E 

Copyright

©

2019 THine Electronics, Inc.                                                                                                        THine Electronics, Inc. 

36/53 

Security E 

 

Multiple camera synchronization Frame Vsync supply 

Frame VSYNC can be supplied from THCV242 to Sub-Link Slave GPO. 

EXTSYNC input or internally generated VSYNC become supply source. Settings are configurable by 2-wire 

access to internal register. When internal VSYNC is selected, generated VSYNC is not only sent to remote Sub-

Link Slave but also output from EXTSYNC pin. 

 

Internal VSYNC uses two clock source, internal oscillator clock and video pixel clock from Main-Link input. At 

the beginning of internal VSYNC generation operation, oscillator clock is used to supply VSYNC. After Main-

Link video source is received stable, internal VSYNC generation source is switched to video pixel clock from 

selected Main-Link input. When Main-Link video pixel clock input is lost, internal VSYNC generator again uses 

internal oscillator clock until Main-Link video pixel clock input is regained. 

 

Table 23.

 

Multiple camera synchronization Frame Vsync supply setting 1/2 

 

 

 

 

bit

Register Name

width

R/W

init

Description

0x10 07

[7:4]

reserved

4

-

-

-

0x10 07

[3:0]

R_EXTSYNC_MODE

4

R/W

4'h0

EXTSYNC I/O Mode
0:Disable
1:Normal Mode (Controlled by Sub-Link Register)
2~F: Reserved

Adr

Summary of Contents for THCV242






















































Reviews:

No comments