THERMOSTAHL ENERDENSE Installation And Service Manual Download Page 3

GENERAL INFORMATION 

 

 

1.

 

GENERAL INFORMATION 

1.1.

 

Proper use of the appliance 

Before  you  make  use  of  this  appliance  make  sure  you  have  read  and  fully  understood  the 
instructions included in this manual.  

The  installation  and  use  of  the  appliance  must  be  performed  according  to  the  instructions 
indicated in this manual in combination with the current national safety regulations.  

The appliance is designed for use in pumped hot water central heating systems. Any other use 
is  considered  improper  and  is  prohibited.  THERMOSTAHL  declines  any  responsibility  for 
damages or injuries caused by 

improper use; in this case the risk is completely at the user’s 

responsibility.  

To ensure an efficient and flawless function of the appliance, it is strongly recommended that 
you have performed an annual service by a qualified technician.  

 

1.2.

 

Safety warnings 

All installation and maintenance procedures must be carried out by professional and authorized 
personnel, in compliance with the indications in the present manual and national regulations. 
Any failure to correctly install this appliance could cause damage or injuries! 

Do not make modifications to parts of the appliance, unless you have contacted the company 
and an authorized service contractor.  

Only original accessories and spare parts must be used to ensure correct and safe function.  

Make  sure  you  respect  the  cleaning  and  maintenance  procedures  on  the  corresponding 
intervals. Failure to do so can cause malfunction to the appliance and possible damages.  

The  boiler  is  design  to  function  on  the  fuels  indicated  in  the  corresponding  paragraph.  Any 
other  fuel  is  prohibited.  Do  not  use  explosive  or  flammable  substances!  Do  not  store  such 
substances inside the boiler room. 

The working pressure varies according to the model. Make sure you use the appropriate water 
pressure. 

Working  in  a  pressure  higher  than  the  one  indicated  in  this  manual  is 

strictly prohibited and dangerous!

 

 

1.3.

 

Data label 

The data label of the appliance is placed on the boiler’s side cover, on the external part. Make 

sure that it is properly placed and readable.  

On the label it is indicated the serial number and the manufacturing year of the appliance. 

 

1.4.

 

Document information 

This  document  is  an  integral  and  indispensable  part  of  the  product  and  must  be  retained  in 
good condition by the user. Keep it in a safe place for future reference. 

If the appliance is sold or transferred to another person, this manual has to always follow the 
appliance and handed to the new user or installer.   

 

 

 

 

 

Summary of Contents for ENERDENSE
























Reviews: