THERMOSALD UPSCR Series Operator'S Manual Download Page 16

Page: 16 / 18

THERMOSALD UPSCR_N_V5 - OPERATOR MANUAL - Rev. 2006 / 07
Page N. 16

- Tot: 18

Verify bands, Verify power connectios between thermoregulator and bands.

F091

FAULT I2T

Verify currents.

F092

POWER PART FAILURE

Hardware problems, press key RESET/MODE, if the problem persists do not exitate to contact our

technichal office.

F093

BAND BROKEN DURING A SEAL

Verify power on the trasformer, Verify Voltage on CN1/1-CN1/2 connector, Verify breaking of power

cables, Verify breaking of bands.

F094

REFERENCE SIGNAL CABLE FROM BAND IS INTERRUPTED

Verify the connections of reference signal cable from band ( CN3/6 - CN3/7 )

F095

MAINS SUPPLY SYNCRONISM DOES NOT MATCH MACHINE REQUIREMENTES

Internal hardware problem, do not exitate to contact our technichal office.

F096

V-I TOO HIGH

Voltage circuit saturation.

Verify trimmer BALANCING

Verify DIP SWITCH SW1 (only previous software up to release 4.0)

F097

PARTIAL SHORT-CIRCUIT BETWEEN THE BANDS

Verify bands into machine, probably not perfectly isolated.

If the problem persist, repeat Burn-in procedure, only few seconds to permit starting of procedure, and press

RESET/MODE to interrupt procedure.

To reduce the problem increase MACHINE DATA 8.XXX (PARTIAL SHORT CIRCUIT)

F098

NO CURRENT DELIVERED DURING CALIBRATION

Verify power on the trasformer, Verify Voltage on CN1/1-CN1/2 connector, Verify breaking of power

cables, Verify breaking of bands.

F099

FAULT EEPROM

Do not exitate to contact our technichal office.

Summary of Contents for UPSCR Series



















Search results

Summary of Contents for UPSCR Series

Reviews:

Related manuals for UPSCR Series

Brands by name

Popular brands

THERMOSALD UPSCR Series, Operator'S Manual

Search results

Summary of Contents for UPSCR Series

Reviews:

Related manuals for UPSCR Series

Brands by name

Popular brands