background image

P a g e

 | 

13 

 

17/03/11 

   

  

 

 
 

        

11. Use the “Home” 

key to return to the original display: 

 
 
 

 

SENSOR CORRECTION 

 

There are a number of factors that will affect the accuracy of the temperature 
displayed in relation to the actual temperature inside the incubator, these include the 
following: 

  Loading of the incubator. (Product load inside the incubator may affect 

the air flow across the temperature sensor). 

  Incubator temperature. (At higher temperatures the heat loss from the 

incubator will be greater). 

  Sensor location. (The temperature sensor can never be placed in the 

centre of the incubator because it could get damaged). 

Because of the above factors, it will be common to have an error between the 
temperature displayed and temperature measured at the centre of the workspace. 
For this reason the digital temperature controls have a parameter that can be used to 
correc

t the temperature displayed, called the “PV Offset”.  

In simple terms this “PV Offset” adds or subtracts a correction value to the displayed 
temperature to make it read the correct temperature. The “PV Offset” correction 
parameter can be accessed by means of the following procedure: 

 

 

MEASURING EQUIPMENT 

Ensure that the equipment used to verify the temperature at the desired location is 
appropriate for conditions, and it has a current certificate of calibration to a traceable 
source issued by a registered organisation.

 

 
 
 

ADJUSTING THE CALIBRATION OFFSET 

As an example, assume that we have determined with our reference instrument that 
@ 35ºC we have a +1.0ºC error, and that we should be reading 36ºC instead of 
35ºC. 

 
 

 

Summary of Contents for TI-150F

















Reviews: