Thermo Scientific SRD-3200 Operating Instructions Manual Download Page 59

Page: 59 / 64

UltiMate 3000 Series:

SRD-3x00 Solvent Racks

Operating Instructions

Page

9.2 Optional Accessories

Description

Part No.

Remarks

Drain kit for UltiMate

3000 systems

6040.0005

The drain kit includes all required components and detailed

installation instructions.

External power supply

unit

6510.0004

To connect the SRD to the power source if the SRD is

not

operated together with the pump of the UltiMate 3000

system.

9.3 Consumables and Spare Parts

Description

Part No.

Solvent supply line (analytical)

6030.2548

Fitting plug degasser

6000.0048

Solvent filter, filter holder (top and bottom parts), pack of 6 filters

6268.0115

Filter frits in the solvent filter

Filter frit, stainless steel, porosity: 10 µm (pack of 10 frits) for

SD(N) pumps
Filter frit, PEEK, porosity: 10 µm (pack of 10 frits) for

BM pumps, NCS-3500RS, and NCP-3200RS
Filter frit, titanium, porosity: 10 µm (pack of 10 frits) for

RS and AB pumps

6268.0110

6828.0117

6828.0111

Solvent reservoir (1-L; with cap)

2270.0012

External power supply unit

6510.0004

Bottle cap for solvent reservoirs

(including caps to close the holes in the bottle cap) 4 caps

6270.0013

Retaining guide (for solvent bottle), pack of 5 guides

6000.0042

Cable connecting the SRD and the UltiMate 3000 system module (pump,

NCS-3500RS, or NCP-3200RS)

6000.1006

Cap (to close the holes in the solvent bottle caps), pack of 20 caps

6000.0047

Caps and retaining guides for solvent bottles, kit of

10 caps (to close the holes in the solvent bottle caps) and

5 retaining guides (for solvent bottle)

6030.9101

Summary of Contents for SRD-3200

































































Search results

Summary of Contents for SRD-3200

Reviews:

Related manuals for SRD-3200

Brands by name

Popular brands

Thermo Scientific SRD-3200, Operating Instructions Manual

Search results

Summary of Contents for SRD-3200

Reviews:

Related manuals for SRD-3200

Brands by name

Popular brands