Thermo Scientific Multiskan Sky User Manual Download | Manualshive

Page: 13 / 42

background image

Thermo Scientific

Thermo Scientific Multiskan Sky User Manual

5

2

Install Multiskan Sky

This chapter describes the necessary installation steps before you can operate the instrument.

Installation order:

1. Remove the transport lock.

2. Connect the mains supply cable.

If you want to connect the instrument to SkanIt Software:

1. Connect the instrument to a computer.

2. Install SkanIt Software.

WARNING

Only authorized technical service personnel are allowed to open the instrument.

Disconnect the instrument from all voltage sources by disconnecting the power supply cable before
opening it.

WARNING

Do not touch switches or electrical outlets with wet hands. Switch the instrument off

before disconnecting it from the mains supply.

WARNING

Do not attempt to operate the instrument with the transport lock in place.

CAUTION

Do not touch or loosen any screws or parts other than those specifically designated in

the instructions. Doing so may cause misalignment and will void the instrument warranty.

CAUTION

Leave the instrument to sit for at least three hours before installing and switching it on

to prevent condensation causing a short circuit.

«
...
11
12
13
14
15
...
»

Summary of Contents for Multiskan Sky











































Reviews:

No comments

Related manuals for Multiskan Sky

Brand: Bamo Pages: 8

Brand: P3 International Pages: 1

Brand: Burkert Pages: 192

Brand: Bamo Pages: 17

In-Situ Rugged TROLL 100

Brand: Geotech Pages: 6

Brand: QUNDIS Pages: 6

Brand: Hanna Instruments Pages: 52

Brand: Vega Pages: 36

Brand: National Instruments Pages: 83

Brand: TE Connectivity Pages: 5

Brand: Omega Engineering Pages: 42

Brand: HACH LANGE Pages: 140

Eniscope Hybrid

Brand: Best.Energy Pages: 52

Brand: LMI Pages: 12

Brand: Capintec Pages: 49

Brand: Circutor Pages: 18

Walk-in Monitoring System 100

Brand: American Panel Pages: 20

Victoreen 948A-40

Brand: Cardinal Gates Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands