Thermo Scientific AquaSensors AquaChlor User Manual Download Page 38

Page: 38 / 43

Thermo Scientific AquaSensors

™

AquaChlor

™

Free Chlorine Monitor User Guide

Free Chlorine System Order Matrix and Accessories

DataStick™ Free Chlorine Sensor Head

Model Number

CL31 Free Chlorine Sensor Head plugs into any DataStick sensor body and provides factory-calibrated

measurement. Integral temperature. Replaceable Membrane Cap.

Sensor Tip Options

B Process Flat (without face seal)

C Face Seal (for flow chamber mounting)

Measurement Range

1 0 to 5 ppm

2 0 to 20 ppm

CL31

DataStick Components

Description

Part Number

Universal Sensor Body

316 Stainless Steel 1” sensor body

CPVC 1-inch sensor body

PEEK® 1-inch sensor body

DS11

DS21

DS31

Communications Adapter

CPVC Modbus RTU with 10 foot cable

CA22B1A

Profibus / DataStick Gateway

Modbus RTU DataSticks connect to Profibus DP

CA26R

Local Interface

Description

Part Number

AV38 Display

One 4-20mA output, PID. 24VDC.

Two 4-20mA outputs, PID, 2 Relays, Modbus Host, 24VDC.

AV38BB0A1

AV38CB4A1

Mounting Hardware

Description

Part Number

1.5” Union Mount Assembly

Stainless Steel

CPVC

MH1041

MH1042

1.5” Tee

Schedule 40, Stainless Steel

Schedule 80, CPVC

MH3011

MH3022

Flow Chamber Assembly

Flow Chamber with mounting plate w/ fittings.

Dual Flow Chamber with mounting plate w/ fittings.

FC001

FC003

Junction box

Extension Cable

For extension cables. Terminal strip included.

DataStick Extension cable

JBOXX01

DSECxx; xx=ft

Product Description

Part

Number

Chlorine Electrolyte

Electrolyte in the PPM range. – 60ml bottle

RDOK9

Membrane Assembly

Chlorine Membrane Cap with pre-stretched membrane

DMR09

Protective Cap

To keep stored membrane wet when stored.

SBC01

Summary of Contents for AquaSensors AquaChlor












































Search results

Summary of Contents for AquaSensors AquaChlor

Reviews:

Related manuals for AquaSensors AquaChlor

Brands by name

Popular brands

Thermo Scientific AquaSensors AquaChlor, User Manual

Search results

Summary of Contents for AquaSensors AquaChlor

Reviews:

Related manuals for AquaSensors AquaChlor

Brands by name

Popular brands