Thermo Scientific AquaSensors AquaChlor User Manual Download Page 31

Page: 31 / 43

Thermo Scientific AquaSensors

™

AquaChlor

™

Free Chlorine Monitor User Guide

When the enter key is pressed, the calibrate menu is displayed. This ends the temperature calibration

procedure. The user has the option of repeating the procedure if desired.

≡

Calibrate

►

Temperature

ESC

ENTER

◄

►

▼

▲

5.5.

Configuration

The complete configure menu for Free Chlorine is shown.

≡

Configure

►

Sensor Filter

ESC

ENTER

◄

►

Temp Filter

►

Temp Units

◄

Exit

▼

▲

►

From the measure screen, press MENU.

From the Main Menu, use the up/down arrows to select Configure. Then press ENTER.

From the Configure menu, use the up/down arrows to select Sensor Filter. Then press ENTER.

≡

Main Menu

►

Configure

ESC

ENTER

◄

►

▼

▲

11.34 ppm
14.3 °C

ESC

ENTER

◄

▲

►

▼

Summary of Contents for AquaSensors AquaChlor












































Search results

Summary of Contents for AquaSensors AquaChlor

Reviews:

Related manuals for AquaSensors AquaChlor

Brands by name

Popular brands

Thermo Scientific AquaSensors AquaChlor, User Manual

Search results

Summary of Contents for AquaSensors AquaChlor

Reviews:

Related manuals for AquaSensors AquaChlor

Brands by name

Popular brands