Thermo Scientific AquaSensors AquaChlor User Manual Download Page 29 | Manualshive

Page: 29 / 43

background image

Thermo Scientific AquaSensors

™

AquaChlor

™

Free Chlorine Monitor User Guide

27

5.4.

Temperature Calibration

Press the ENTER key from the TEMPERATURE calibration menu to initiate the calibration process.

When the temperature calibration procedure is started, the analog output is placed into hold mode. The
user is prompted to prepare the sensor. The sensor value is dynamically updated during this step.

When the sensor is ready, the ENTER key is pressed and the user is presented with a calibration value for
editing. Please note that it is best to calibrate temperature when the sample chamber is full of flowing

process water.

≡

Calibrate

►

Temperature

MENU

ESC

ENTER

◄

►

▼

▲

Temperature?
( 25.3) °C

MENU

ESC

ENTER

◄

►

▼

▲

25.3 °C
Sensor ready?

MENU

ESC

ENTER

◄

►

▼

▲

«
...
27
28
29
30
31
...
»

Summary of Contents for AquaSensors AquaChlor












































Reviews:

No comments

Related manuals for AquaSensors AquaChlor

Brand: Olympus Pages: 86

Brand: Labnet Pages: 5

Brand: C.M.O Pages: 10

Brand: Rapid Technic Pages: 152

Brand: JB-Lighting Pages: 40

Brand: Landoll Pages: 70

Brand: Landice Pages: 19

Brand: Landice Pages: 7

Brand: H&S Pages: 42

Brand: Pani Pages: 12

Brand: FASTER TOOLS Pages: 19

Brand: Qlight Pages: 4

Brand: Warner Electric Pages: 14

Brand: ABB Pages: 106

Brand: Measumax Pages: 2

Brand: Woods Pages: 40

Brand: Lutron Electronics Pages: 10

Brand: Mikrona Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands