Texmate Tiger 320 GI-50E, Manual

Page: 35 / 44

Apr-08-2016 GI-50 320 DS (NZ308)_UL April 2016 Page 35 Texmate, Inc. Tel. (760) 598-9899 • www.texmate.com
Setpoint Programming Mode continued Setpoint Programming Mode continued
P
X X
P
P P
XX XX
P P P
XX
P P P P
XX
P P P P
XX
P P P
XX
P P P P
XX
P P
P
P
XX
Single actuation
P
P
P
P
Use the and
buttons to cycle
through the options
[brEAK]
[both]
[LEVEL]
[Ch4] [tot_1]
[diSP]
[rESLt]
[Ch1]
[Ch2]
[Ch3] [tot_2]
[PEAK]
[VALEY]
[tArE]
[244 to 1]
Use the but-
tons to cycle through
the Registers Menu
and Registers (1 to
244) to select which
destination register
is to be reset by a
setpoint (also see
page 36).
[i-S+C]
[d+C]
[rEG]
Sets from 0 to –19999
Sets from 0 to 99999
Select Reset Destination Register
Select Trigger Setting
Select Reset Mode
Select Reset Constant
P
Select Print Triggered by Setpoint
P
Select Log Triggered by Setpoint
Set Up Register Reset and Setpoint Trigger Functions
Third digit
set to [XX7]
Selecting any
destination
register takes
you to Mode
Reset
Selecting [oFF] in the
Destination Register
Reset Setup takes
you to Setpoint Print
Trigger Setup
P
Use the but-
tons to cycle through
the Registers Menu
and Registers (1 to
244) to select which
register’s contents
are to be copied
into the destination
register by a setpoint
(also see page 36).
Set Up Timer Delay Settings
Third digit
set to [XX6]
Delay-on-make (DOM)
time 0.0 to 6553.5 secs Delay-on-break (DOB)
time 0.0 to 6553.5 secs
Reset SPC_X to [XX0]
DOM 0.0 to 6553.5 secs Minimum on-time (M_on) 0.0 to
6553.5 secs
On-time (on _t) 0.0/0.001
to 6553.5/65.535 secs
On-time (on _t) 0.0/0.001 to
6553.5/65.535 secs
DOB 0.0 to 6553.5 secs
Off-time (oFF_t) 0.0/0.001 to
6553.5/65.535 secs DOB 0.0/0.001 to
6553.5/65.535 secs
On-time (on _t) 0.0/0.001
to 6553.5/65.535 secs
Off-time (oFF_t) 0.0/0.001 to
6553.5/65.535 secs
Off-time (oFF_t) 0.0/0.001
to 6553.5/65.535 secs
Minimum off-time (M_of)
0.0 to 6553.5 secs
X X
X X
Reset SPC_ X to [XX0]
P
Programming Tip
If you do not require any
of the functions in this
mode, ensure it is set to:
Programming Tip
If you do not require any
of the functions in this
mode, ensure it is set to:
Resolution setting
applies to SP1/SP2
ONLY
Resolution setting
applies to SP1/SP2 ONLY
Normal Mode
1-Shot ON Mode
Pulse ON Mode
Repeat ON Mode
1-Shot OFF Mode
Pulse OFF Mode
Repeat OFF Mode
DOM 0.0/0.001 to
6553.5/65.535 secs
Select [rEG] to
access the source
parameter to select
the number of the
Modbus register in
the meter to be cop-
ied to the reset desti-
nation register
Resolution setting
applies to SP1/SP2
ONLY
Resolution setting
applies to SP1/SP2
ONLY
Normally OFF /
Pulsed ON
Normally ON /
Pulsed OFF
Single actuation
Multiple actuation
Single actuation
Single actuation
Multiple actuation
[Ch4] [tot_1]
[diSP]
[rESLt]
[Ch1]
[Ch2]
[Ch3] [tot_2]
[PEAK]
[VALEY]
[tArE]
[244 to 1]