57
ENG
7.
HEALTH button
Press this button, you can turn on or off the health function.
8.
SLEEP button
• Press the SLEEP button, the sleeping indicator light of indoor unit flashes on.
• The air-conditioner runs in sleeping mode for 10 hours and quit sleep mode, recover back to former mode.
• The unit will turn off automatically if the timing mode are running out of time.
Note
: press the MODE or ON/OFF button, the remote controller clears sleeping mode away.
9.
iFEEL button
• Press this button can be used to set the feeling function. The LCD shows the actual room temperature when
the function set and it shows the setting temperature when the function cancelled.
• This function is invalid when the appliance at the Fan mode.
10.
DISPLAY button
• In display mode, press button once, shut off display, press it again, LCD will show ambient & setting
temperature after flashing 5s. It’s convenient for users who are not adapt to noctilucence and it’s also
convenient for checking ambient & setting temperature anytime.
11.
iCLEAN button
• When remote controller is at the off state, press “
iCLEAN
” button, the unit runs “
iCLEAN
” function.
• The purpose of this function is to clean dust on evaporator and dry the inside water of evaporator and to
prevent the evaporator going moldy due to water deposition and boasting strange smell.
• After setting “
iCLEAN
” function, press “
iCLEAN
”button or “ON/OFF”button to quit it.
• The clean function will be stop working after about 30 minutes running working without any operation.
12.
ELE.H button (only for hot pump type)
• In heating mode, press this button, the mode of operation is shifted into supplementary electric heating.
13.
Anti-FUNGUS button
•
The purpose of this function is to dry the inside of the evaporator and to prevent the evaporator from going
mouldy due to water deposition and thus dispersing strange smell.
• This function is controlled by the remote controller under cooling, dry and auto (cooling and dry) modes,
the horizontal wind guiding bars are at the initial position for cooling. The A/C runs under heating mode(the
cooling only A/C only runs under fan mode), the internal fan runs for 3 minutes with weak wind before stop.
• This function has not been set in the factory. You may freely set and cancel this function. The setting method
is: under “off”status of the A/C and the remote controller, point the remote controller toward the A/C and
continuously press “
Anti-FUNGUS
”button for one time, the buzzer keep beeping five times again after five
times beep, indicating that this function is ready. In case this function has been set, unless the whole A/C is
powered off or the function is manually cancelled, the A/C then has this function as default.
• To cancel the function:
1. Under “off”status of the A/C and the remote controller, point the remote controller toward the A/C and
continuously press “Anti-FUNGUS”button for one time, the buzzer keep beeping three times again after five
times beep, indicating that this function has been cancelled;
2. Power off the whole A/C.
• When this function is on, it is suggested not to restart the A/C before it is completely stop.
• This function will not run in case of time stop.
14.
SPOT SWING button
• Press this button, the horizontal wind direction vanes can swing automatically, when you have the desired
vertical wind direction.
• Press it again, the horizontal wind direction vanes will be stopped at the situation of your choice.
15.
ECO button
• In cooling mode, press this button, the unit will runs “ECO” economic operation mode which costs the least
power consumption.
• After running for 8h, it will automatically exit, otherwise, press this button once again to quit it.
Note
: The unit will turn off automatically if the timing mode are running out of time.
16.
“iFavor“ button
The button is a shortcut button, users could reserve the data of mode, wind speed, set temperature, swing and
when pressing on it, it could operate in the mode users set before.
Method 1
: turn on the air conditioner, make adjustment to the ideal mode you wanted.
Method 2
: keep pressing the shortcut button for three seconds, till the display screen give the signal that
represents the shortcut button and glitter for three times, then reserve the operation mode in the remote
controller, it’s done. To take place of the previous operation mode, just do it as shown above.
Summary of Contents for TA22FFML-07410A
Page 59: ......
Page 60: ...www tesla info ...
