manualshive.com logo in svg

TESA MH3D, User Manual

Share
Download
TESA MH3D User Manual Download Page 83

User's Manual

MH3D

©2004 TESA Switzerland All Rights Reserved.

Page 5-15

Glossary

Out-of-Tolerance

The condition in which a feature is larger or smaller than
its specified dimension.

Output

Information displayed or printed by a computer.

Parallelism

The condition in which all points on a surface or axis are
equidistant from a datum plane or axis. A measurement
routine where two features are parallel within a specified
tolerance of size. One feature is the datum and the other
is the toleranced line.

Part Alignment

The process of mathematically aligning the measurement
axes of the CMM with the part axes.

Part Axes

The X, Y, and Z axes of a part.

Part Coordinates

X, Y, and Z values that have been modified by part
alignment.

Part Orientation

The alignment of an object with respect to a known
reference.

Part Program

A list of coded instructions that tells the system how to
measure a part on a CMM.

Part Program

A storage area that holds part programs.

Directory

Part Program Name

A label assigned to a part program. It is saved, retrieved
and reused by means of this name.

Part Reference

The axes alignment, datum position and working plane

Frame

under which measurements are made.

Part Unnamed Axis

The axis not named in the part’s working plane.

Passive Probe

A solid or hard probe which mechanically fixes the
movable components relative to the workpiece.

Password

A word entered at the computer keyboard to gain access
to programs or information stored in a computer.

Performance Test

Any of a number of test procedures used to measure
machine performance.

Periodic Error

An error in the linear displacement accuracy of a ma-
chine that is periodic over an interval which normally
coincides with a natural period of the machine scales.

Summary of Contents for MH3D







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands