TESA MH3D User Manual Download Page 11

Page: 11 / 102

User's Manual

MH3D

Page 1-7

The MH3D Machine

The MH3D Coordinate Measuring Machine features a lightweight, table top, bridge
type design with a removable granite support.

This machine is designed to accommodate moderate sized work pieces with an
economical table mounted unit.

This series of machines incorporates the following features:

•

A granite worktable that provides a stable, precision measuring surface
that is practically maintenance free.

•

M10 threaded, stainless steel inserts imbedded into the granite table for
securing the workpiece.

•

Air bearings for frictionless movement of all axes.

•

A fully pneumatic, counterbalanced column, infinitely adjustable for
varying probe weights, with a built-in braking device.

•

A Z-Rail Probe Holder that accommodates a wide variety of probes and
accessories.

•

A machine construction that allows accurate measurement of steel
parts over a wide temperature range.

•

A control interface with pushbutton access to data display and analysis.

•

A bright, clear VGA monitor.

Description

Summary of Contents for MH3D
















































































Search results

Summary of Contents for MH3D

Reviews:

Brands by name

Popular brands

TESA MH3D, User Manual

Search results

Summary of Contents for MH3D

Reviews:

Brands by name

Popular brands