manualshive.com logo in svg

TESA MH3D, User Manual

Share
Download
TESA MH3D User Manual Download Page 67

Page 4-11

©2004 TESA Switzerland All Rights Reserved.

User's Manual

MH3D

Cleaning Glass Scales

If it is necessary to clean the glass scales on the MH3D, proceed as follows:

Cleaning the X Axis Scale
• 

Move the bridge to the rear of the

machine.

• Move the ZX cariage to one end
  of its travel.  Lock the machine's
  axes.

• 

Clean the measuring scale with a

  soft, anti-static cloth that is
  moderately wetted with pure
  alcohol.  

Use only Isopropyl

  Alcohol.

 Allow the alcohol to dry.

  

NOTE:

 Do not use any other

  type of cleaning fluid.

• 

Unlock the axes and move the

  bridge or carriage to the other
  end of its travel.  Lock the
  machine axes.  Clean the exposed
  part of the scale.  It is important
  that all residue be removed from the scale.

• 

Check all surfaces for smudges and reclean as required.

• 

Unlock the axes and move the ZX carriage to the middle of the X-axis rail and

lock the machine's axes.

Cleaning the Y Axis Scale
• 

Move the bridge to the rear of the

 

machine. Lock the machine's axes.

• 

Clean the measuring scale with a soft, anti-static cloth that is moderately wetted

with pure alcohol.  

Use only Isopropyl Alcohol.

 Allow the alcohol to dry.

  

NOTE:

 Do not use any other type of cleaning fluid.

• 

Unlock the axes and move the bridge  to the other end of its travel.  Lock the

machine axes.  Clean the exposed part of the scale.  It is important that all
residue be removed from the scale.

• 

Check all surfaces for smudges and reclean as required.

Cleaning the Z Axis Scale
• 

Move the bridge to the rear of the

 

machine.

• Lower the Z-axis rail to its lowest point.
• Lock the machine axes.

• 

Clean the exposed end of the measuring scale with a soft, anti-static cloth that is

moderately wetted with pure alcohol.  

Use only Isopropyl Alcohol.

 Allow the

alcohol to dry. It is important that all residue be removed from the scale. Check
all surfaces for smudges and reclean as required.

  

NOTE:

 Do not use any other type of cleaning fluid.

 

 NOTE:

 Because the end of the scale on the Z-axis is not normally exposed

  during operation, it is not anticipated that it will require periodic cleaning.

The scales are fitted with covers that must be removed before the scales can be
cleaned.  Be sure the covers are cleaned and returned after cleaning the scales.

X Scale

Z Scale

Y Scale

Summary of Contents for MH3D







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands