manualshive.com logo in svg

TESA MH3D, User Manual

Share
Download
TESA MH3D User Manual Download Page 31

User's Manual

MH3D

©2004 TESA Switzerland All Rights Reserved.

Page 2-15

Electronic System

Z-Rail Mouse

The entry of menu selec-
tions and the recording of
measurements are done by
means of the ZMouse

®

 with

its cursor movement,
measurement and select
buttons.

To select a menu item or a
softkey, move the cursor
using the Cursor Movement
Button (Mouse) to highlight
the item.  Press the "Select"
button on the mouse to
activate the item.

Measurement points are
taken by pressing the
"Measurement (XYZ)"
button on the mouse after
positioning the hard probe
on the desired surface of the
part.  Measurement points
can also be taken by
deflecting an electronic probe (TTP) on the part surface.

Select

Measurement
XYZ

Cursor
Movement

The display screen is a VGA monitor with large easy to read characters and a
choice of languages.  The display provides XYZ readout, menu selections and
data input capabilities. The control has an adjustable mounting so it can be set at
a comfortable operating position.

A port is provided for connection of a printer

Summary of Contents for MH3D







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands