TESA MH3D User Manual Download Page 68

Page: 68 / 102

Page 4-12

User's Manual

MH3D

CAUTION

Be sure air pressure is shut off before attempting maintenance work on
the air

system. Make sure the bowl is properly in place and latched before

turning on

air pressure.

If it becomes necessary to replace an air filter or a filter element, obtain one from
the factory. To replace the filter:

Turn off air to machine at supply. Make sure air pressure has gone to zero.

Using the release latch, remove steel bowl guard shield from filter.

Remove plastic filter bowl.

Unscrew filter element.

Assemble the new filter element and replace bowl and shield.

•

The coalescing filter element may be washed in safety solvent and then dried

and reused once or twice and then replaced. Air filters should be washed or
replaced at intervals of 6 months if the air line is dirty.

•

The coalescing filter has an O-ring on its upper surface. Be sure the O-ring is

seated properly in the groove before reinstalling.

• If the filter gets dirty fairly quickly, place another air filter/regulator upstream

of the machine.

• If excessive water is present within the air system at your facility use a

Refrig-

erated Air Dryer

Changing the Air Filter

Air Inlet

70-120 psi

(4.8-8.3 BAR)

Automatic Drain

Particle Filter

Pressure Gage

Particle Filter

Pressure Adjust
Lock Knob

To Machine
58 psi (4 BAR)

Automatic Drain

*Not Shown - Optional Air

Saver Valve

Summary of Contents for MH3D
















































































Search results

Summary of Contents for MH3D

Reviews:

Brands by name

Popular brands

TESA MH3D, User Manual

Search results

Summary of Contents for MH3D

Reviews:

Brands by name

Popular brands