TESA MH3D User Manual Download Page 39

Page: 39 / 102

User's Manual

MH3D

Page 3-5

Operator Safety

• Never lay tools on the machine where they can interfere with its

operation.

• Before using the machine, look for workpiece or other obstructions.

• Report any unusual noise from the machine. Defects should be repaired

immediately.

Never operate the machine in a defective condition.

• Before mounting work holding devices or workpieces, be sure that all

mounting surfaces are clean and free of chips, particularly the bearing
surfaces.

• Keep hands away from all guards and openings in covers when moving

the bridge or carriage.

• Tables, rails, housings and their related parts can create pinch points. Be

sure you are clear of such locations before operating the MH3D.

• Never remove WARNING and/or INSTRUCTION plates from the

machine.

• During service, it may be necessary to remove or open some guards. If

so, use great caution around exposed mechanisms. Make sure all guards
are returned and in place when set-up work is completed.

• Do not allow the bridge, carriage or rail to impact the end stops with a

high amount of force at the ends of the measuring range. Bring the
machine to a gentle stop.

• Do not allow the probe body or Z-rail to strike the workpiece or work

table.

• Do not allow the probe to strike the workpiece with high force. Refer-

ence the probing technique section of this manual.

• Do not attempt to move the bridge, carriage, or Z-Rail while air pressure

is below the value listed in the specification section. Serious damage to
the machine will result. Do not attempt to move the machine with the
axes switches down.

• Always hold the Z rail firmly when unlocking the Z axis lock.

• Lock the machine axes when the machine is not in use.

Summary of Contents for MH3D
















































































Search results

Summary of Contents for MH3D

Reviews:

Brands by name

Popular brands

TESA MH3D, User Manual

Search results

Summary of Contents for MH3D

Reviews:

Brands by name

Popular brands