Terasic TSOM Manual Download Page 31

Page: 31 / 62

TSoM Evaluation
Kit User Manual

www.terasic.com

July 26, 2019

Table 5-1 Pin Assignment of Slide Switches

Signal Name

260-pin Edge Connector

Pin No.

FPGA Pin No.

Description

I/O Standard

SW0

PIN_112

PIN_AC24

Slide Switch[0]

3.3V

SW1

PIN_114

PIN_AB23

Slide Switch[1]

3.3V

Table 5-2 Pin Assignment of Push-buttons

Signal Name

260-pin Edge Connector

Pin No.

FPGA Pin No.

Description

I/O Standard

KEY0

PIN_37

PIN_D11

Push-button[0]

3.3V

KEY1

PIN_39

PIN_AB25

Push-button[1]

3.3V

Table 5-3 Pin Assignment of LEDs

Signal Name

260-pin Edge Connector

Pin No.

FPGA Pin No.

Description

I/O Standard

LED0

PIN_205

PIN_AA26

LED [0]

3.3V

LED1

PIN_206

PIN_W12

LED [1]

3.3V

The board has two TMD connectors, each connector has 8 user pins connected to the
260-pin Edge Connector (to Cyclone V SoC FPGA). It also comes with DC +3.3V (VCC3P3), and
two GND pins.

Figure 5-5

shows the I/O distribution of the TMD connector. The maximum power

consumption allowed for a daughter card connected to one or two TMD ports is shown in

Table 5-4

and

Table 5-5

, shows all the pin assignments of the TMD connectors.

Summary of Contents for TSOM































































Search results

Summary of Contents for TSOM

Reviews:

Related manuals for TSOM

Brands by name

Popular brands

Terasic TSOM, Manual

Search results

Summary of Contents for TSOM

Reviews:

Related manuals for TSOM

Brands by name

Popular brands