Teracom TCW242-S, User Manual

Page: 26 / 52

TCW242-S_R1.0 – July 2021 Page 26
9. Protocols and API
9.1. SNMP
Simple Network Management Protocol (SNMP) is a standard internet protocol for managing devices
on IP networks. In typical usage of SNMP, one or more administrative computers, called managers,
monitor and control devices on LAN. Each controlled device, at all times, executes a software
component called an agent which reports information via SNMP to the manager.
The TCW242-S can be configured and monitored through SNMP.
This could be done using every SNMP v.2 or v.3 compatible program. Parameters that can be
changed, are grouped according to their functions in the tables below. To obtain a valid OID
number, replace the symbol “
! ” with ”1.3.6.1.4.1.38783”.
To save the changes configurationSaved (OID !.8.6.3.0) should be set to "1".
product
OID Name Access Description Syntax
!. 8.1.1.0 name read-only Device name DisplayString
!. 8.1.2.0 version read-only Firmware version DisplayString
!. 8.1.3.0 date read-only Release date DisplayString
setup -> network
replace “ ! ” with ”1.3.6.1.4.1.38783” in the table below
OID Name Access Description Syntax
!. 8.2.1.1.0 deviceID read-only Device ID (default MAC address) MacAddress
!. 8.2.1.2.0 hostName read-only Hostname
DisplayString
(SIZE (0..38))
!. 8.2.1.3.0 deviceIP read-only Device IP address IpAddress
setup -> parameters -> mbSensors -> mbSensorsTable -> mbSensorsEntry -> msSensIndex 1 to 24
replace “ ? “ with a number from 1 to 24 and “ ! ” with ”1.3.6.1.4.1.38783” in the table below
OID Name Access Description Syntax
!. 8.2.2.1.1.1.2. ? .0 mbSenDescription. ? read-write Sensor description DisplayString
!. 8.2.2.1.1.1.3. ? .0 mbSenMult. ? read-write Sensor multiplier x1000 in Integer format Integer32
!. 8.2.2.1.1.1.4. ? .0 mbSenOffset. ? read-write Sensor offset x1000 in Integer format Integer32
!. 8.2.2.1.1.1.5. ? .0 mbSenVal. ? read-only Sensor value x1000 in Integer format Integer32
!. 8.2.2.1.1.1.6. ? .0 mbSenCounter. ? read-only Sensor as 32-bit Counter Counter32
setup -> parameters -> analogInputs -> analogInpTable -> analogInpEntry -> analogInpIndex 1 to 4
replace “ ? “ with a number from 1 to 4 and “ ! ” with ”1.3.6.1.4.1.38783” in the table below
OID Name Access Description Syntax
!. 8.2.2.2.1.1.2. ? .0 analogInpDescription. ? read-write Analog input description DisplayString
!. 8.2.2.2.1.1.3. ? .0 analogInpMult. ? read-write Analog input multiplier x1000 in Integer format Integer32
!. 8.2.2.2.1.1.4. ? .0 analogInpOffset. ? read-write Analog input offset x1000 in Integer format Integer32
!. 8.2.2.2.1.1.5. ? .0 analogInpMode. ? read-write Analog input mode - 0-10V or 4-20mA Integer32
!. 8.2.2.2.1.1.6. ? .0 analogInpValue. ? read-only Analog input value x1000 in Integer format Integer32
setup -> parameters -> digitalInputs -> digitalInpTable -> digitalInpEntry -> digitalInpIndex 1 to 4
replace “ ? “ with a number from 1 to 4 and “ ! ” with ”1.3.6.1.4.1.38783” in the table below
OID Name Access Description Syntax
!. 8.2.2.3.1.1.2. ? .0 digInpDescription. ? read-write Digital Input description DisplayString
!. 8.2.2.3.1.1.3. ? .0 digInplowLevel. ? read-write Digital Input closed state DisplayString
!. 8.2.2.3.1.1.4. ? .0 digInphighLevel. ? read-write Digital Input open state DisplayString
!. 8.2.2.3.1.1.5. ? .0 digInpMode. ? read-write Digital Input mode - Discrete or Counter
INTEGER {
openclosed(0),
risingEdge(1),
fallingEdge(2),
bothEdges(3)
}