Tenda DH301 User Manual Download Page 50

Page: 50 / 120

Wireless N300 ADSL2+ High Power Modem Router

Step 4:

Enter PPP username and its password provided by your ISP. Click

Next

PPP Username:

This is for logging in to your ISP. If you cannot locate this information, ask your ISP to provide it.

PPP Password:

This is for logging in to your ISP. If you cannot locate this information, ask your ISP to provide it.

Authentication Method:

This is used by ISP to authenticate the client that attempts to connect. If you are not sure,

consult your ISP or select

AUTO

Dial on demand:

Connect to ISP only when there is traffic transmission. This saves your broadband Internet service bill.

Enable PPP Debug Mode:

Only enable this feature if supported by your ISP.

Multicast Proxy:

If enabled, the router will use multicast proxy.

If you are not sure about the options on this screen, simply enter your ISP user name and password and leave the other

options unchanged from defaults. Click

Next

to enter the following screen.

Summary of Contents for DH301

























































































































Search results

Summary of Contents for DH301

Reviews:

Brands by name

Popular brands

Tenda DH301, User Manual

Search results

Summary of Contents for DH301

Reviews:

Brands by name

Popular brands