manualshive.com logo in svg

Tenda DH301, User Manual

Share
Download
Tenda DH301 User Manual Download Page 25

                                                                                                              Wireless N300 ADSL2+ High Power Modem Router

 

21 

only by cloning the MAC address of your computer can you access the Internet through the router. 

2. 

MTU

:

  Short  for 

M

aximum 

T

ransmission 

U

nit,

 the  largest  physical packet  size,  measured  in bytes,  which 

a network can  transmit.  Any  messages  larger  than  the  MTU  are  divided  into  smaller  packets  before  being  sent.  The 

default MTU is 1492 bytes. For some ISPs, you might need to change the MTU. This is rarely required, and should not 

be done unless you are sure it is necessary for your ISP connection. 

 

Step  5: 

To  configure  the  Default  Gateway  interface,  select  the  interface  that  you  want  to  configure  with  the  WAN 

gateway address in 

Available Routed WAN Interfaces

 box and move it into 

Selected Default Gateway Interfaces 

box. 

The default setting is recommended. Then click 

Next

. 

 

 

Step 6:

 To configure the WAN DNS address, click the 

Select DNS Server Interface

 

from available WAN interfaces 

option,  or  select  the 

Use  the  following  Static  DNS  IP  address 

option  and  enter  the  static  DNS  server  IP  addresses 

provided by your ISP. At last, click 

Next

.

 

Summary of Contents for DH301

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands